KQ-OMS0022 Replace the product in the case of failure such as difficulty removing or inserting tubing. 11 - 5. Construction Male connector Male elbow No.
Maintenance 11 9. Mounting accessories (option) 12 10.
Since cylinders receive excessive force in such a case, do not design circuit synchronizing cylinders only. 11. Mounting Methods Various mounting methods are available as follows. Bottom mounting Side mounting 11-1. Cautions on Mounting 1) Never place your hands or fingers between the plate and the body.
Auto switches When an auto switch is mounted or its set position is changed, refer to pages 11 to 17. Caution Use a specific mounting bracket (Table 3 on page 12.) and mount the product so that the band of the bracket will be perpendicular to the stroke of the product. Tighten mounting screws to the appropriate torque.
0.13 the values in the table 11. 20 0.24 Piston speed has to be less than the allowable value 25 0.45 32 0.88 40 1.53 23/28 6.
As shown in Fig. 11, hold the piston seal with one hand and push it into the groove so that the piston seal can be lifted off and pulled out without using a precision screwdriver. The groove of the rod cover is deep, so if the rod seal is removed with a precision screwdriver, it might be damaged. Fig 10. Remove rod seal Pinch and pull out Fig 11.
Refer to the Material Safety Data Sheet (MSDS) of the hydraulic fluid when supplying the fluid. 11 - 3. Maintenance 3-1. Precautions Warning 1. Maintenance should be performed according to the procedure indicated in the Operation Manual. If handled improperly, malfunction and damage of machinery of equipment may occur. 2. If handled improperly, compressed air can be dangerous.
The value of the residual pressure can be checked using the outlet pressure gauge. 11.
Also make sure that the rotational torque applied to the cylinder body does not exceed the allowable rotational torque (given on page 11). (Otherwise, the excessive rotational torque will damage the non-rotating mechanism and lead to a malfunction.) 6.
PP depth element Nominal filtration accuracy: 1 to 75m Material: PP EJ202S ... x 11 (L125) EJ302S ... x 11 (L250) EJ402S ... x 11 (L500) b Set the stopper on the retainer while holding down the V-band outside perimeter, and then tighten the wing bolt to the prescribed position.
Nil T F Rc NPTF, NPT G Caution 3 position closed center 3 position exhaust center Refer to pages 5-11-2 to 5-11-6 for Safety Instruction and Solenoid Valve Precautions. 5-3-1 2 Series VZA2000 Dimensions: Body Ported 2 position single: VZA2121-M5 2 position double: VZA2221-M5 2-2.8 mounting hole 2-2.8 Mounting hole Pilot port (A side) M5 x 0.8 Pilot port (A side) Pilot port (B side) 2-2.8
Made to Order Specifications (For details, refer to page 3-6-11.)
A 15 3 3 4 5 6 7 8 9 10 11 12 13 Station 5 16 17 18 19 20 21 22 23 24 25 SOL. B 16 SOL. A 4 Station 6 SOL. B DIN rail mounting bracket [-D] VVQ1000-57A for {F, L, M, P, S (EX500) kit} VVQC1000-57A-S for {S (EX250) kit} VVQC1000-57A-T for {T, S (EX126) kit} 17 SOL. A 5 Station 7 SOL. B 18 SOL. A 6 Station 8 SOL.
J D-X 20Data 10-17-11 Series CC Maximum Driving Speed of Cylinders (Speed controller) If intricate speed control is unnecessary and the changes in speed due to load fluctuations can be tolerated, the pneumatic speed controller can be used as a control valve. The minimum controllable flow volume of the speed controller is 3 dm3/min.
11 0.50 0.40 0.40 0.45 0.50 0.40 0.38 0.38 1.1 1.8 2.3 0.75 1.1 1.8 2.8 2.8 6 8 1.5 0.4 340 10 4.5 6 8 250 1.0 3 8 (10A) 340 0.4 10 10 1 2 (15A) 420 Note) Refer to Glossary on page 17-3-15 for details of max. operating pressure differential and max. system pressure.
Filter JIS Symbol 32 41 51 2 x R1.8 1 10 8.8 (Mounting hole) 3.6 19 4.8 (Mounting hole) Filter M5 (or M6) IN port M5 (or M6) OUT port 2 x 3.5 (Mounting hole) (62) 58 50 8 OUT IN 18 15.5 4 11 20 4.2 6.8 11 8.8 Bracket A (Standard accessory) Note) Dimensions : For A mounting bracket. Filter case About this product Caution The filter mounted on the product is a simplified one.
Circuit example/Built-in solenoid valve Ball valve FLUID OUT Regulator AIR EXH Filter AIR SUP FLUID IN Air supply Process pump PB1011 Transfer fluid 19 Process Pump Built-in Solenoid Valve Type/Air Operated Type Series PB1000 Dimensions/Built-in Solenoid Valve Type/Air Operated Type PB1000 FLUID OUT Rc 1/8 11 OUT 11 84 72 Mount with this surface (OUT port side) on top 7.5 41 60 45 UP SIDE
Installation. 11 2. Hardware Specification. 3 1. Introduction. 1 3.1 DIN RAIL Mounting . 11 3.2 Termination at Screw Terminals . 11 3.3 Installation Mounting Notes. 12 2.1 Available Models. 3 2.2 Power Supply Specification . 4 2.3 Input Specification. 5 2.4 Output Specification. 7 2.5 General Specification. 8 iii PneuAlpha 4. Wiring . 13 6.
The example screen shown at the right shows that the Output will turn ON at the following times: The rst week of the month on Monday, Wednesday, and Saturday at 11:30 AM. The third week of the month on Monday, Wednesday, and Saturday at 11:30 AM.
Circuit example/Built-in solenoid valve Ball valve Regulator FLUID OUT AIR EXH Filter AIR SUP FLUID IN Air supply Process pump PB1011 Transfer fluid 17-5-166 27 Series PB Process Pump: Built-in Solenoid Valve Type/ Air Operated Type (External Switching Type) Dimensions PB1000 FLUID OUT Rc 1/8 VC 11 OUT VDW 11 VQ 84 72 VX2 Mount with this surface (out port side) on top 7.5 41 60 45 VX Courtesy