KA KAR08-12 42 4.6 12 10 KAR10-12 44.5 33 32.8 32.8 12 20 21 18.5 15-3-24 Safety Instructions These safety instructions are intended to prevent a hazardous situation and/or equipment damage.
Port size(R) 12 Max. Operating Pressure (MPa) 0.7 Max. Operating temp.
A Note 1) 4 6 4 6 8 4 6 8 10 6 8 10 12 10 12 AS121FP-M5-04 AS121FP-M5-06 AS221FP-01-04 AS221FP-01-06 AS221FP-01-08 AS221FP-02-04 AS221FP-02-06 AS221FP-02-08 AS221FP-02-10 AS321FP-03-06 AS321FP-03-08 AS321FP-03-10 AS321FP-03-12 AS421FP-04-10 AS421FP-04-12 28 7 7 18.4 23.2 8 10.4 22.2 25 25.5 28.3 9.6 M5 x 0.8 12.2 29 8 8 19.4 24.2 12.8 32.4 17 17 18.4 25.3 10.4 27.4 32.4 31.4 36.4 14.2 12
Operating environment Do not allow corrosive fluids or solvents, etc., to come into contact with the outer surfaces of the pump. Do not use in water (or other liquid). Fluid may leak into the pilot switching valve and there may be corrosion of external parts, etc. 2. Low temperature operation Do not allow freezing.
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate or set with wet hands. This may lead to an electric shock. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result.
Solenoid valve side pin wiring diagram Since voltage specifications other than standard 24 and 12 VDC do not have diodes for polarity protection, be careful not to make errors in the polarity. When wiring is done at the factory, positive (+) is red and negative () is black.
Note There are two types of bodies, which are 12-2 and 12-3 described above according to the model. Please note that the applicable model cannot be changed by switching these two types of products.
Disassembly Drawing of the Pressure Gauge Port [Applicable model: without pressure gauge / with pressure gauge (round type)] (12) Plug assembly (12) Plug assembly (3) Pressure gauge (round type) Micro mist separator regulator 12-3.
CJ-CF006 CJ-CR006 M3 x 0.5 6 6 8 11 8 5 6 10 CJ-T010B CJ-CF010 CJ-CR010 3.3 M4 x 0.7 10 8 10 13 10 6 8 29 2 9 4.5 3.1 18 40 22 32 12 8 +0.048 0 16 CJ-T016B CJ-CF016 CJ-CR016 5 M5 x 0.8 16 10 12 15 7 12 10 35 14 5.5 6.4 2.3 20 48 28 38 16 10 +0.048 0 6-3-11 12 12 Series CJ2 Proper Auto Switch Mounting Position (Detection at stroke end) and Its Mounting Height Auto switch Solid state switch
Do not use the product in the presence of a magnetic field. Malfunction can result. Do not let foreign matter, such as wire debris, get inside the product. Otherwise it can cause damage or malfunction. Do not use the product in an environment that is exposed to temperature cycle.
Do not use in an atmosphere having corrosive gases, chemicals, sea water, water, water steam, or where there is direct contact with any of these. 2. Do not use in explosive atmospheres. 3. Do not use in locations subject to vibration or impact. 4. Do not use in locations where radiated heat will be received from nearby heat sources. 5.
12 stations F 1 to 12 Manifold is 12 stations max.
Do not touch the span calibration trimmer except when performing span calibration. Touching the trimmer may cause generation of an error in the measured pressure. Also do not turn it too hard (0.3 Nm or less) or press it too hard (5 N or less). 7. Use a soft cloth to wipe the blot off of the body.
Do not touch the span calibration trimmer except when performing span calibration. Touching the trimmer may cause generation of an error in the measured pressure. Also do not turn it too hard (0.3 Nm or less) or press it too hard (5 N or less). 7. Use a soft cloth to wipe the blot off of the body.
4 6.8 55.3 8.5 13.9 7 52.3 45.3 7 9 3 M10 x 1.0 14 4 8.7 62.3 10 16.2 12 79.1 67.1 8 12 5 M14 x 1.5 19 6 12 92.6 13.5 21.9 15 88.2 73.2 10 17 6 M20 x 1.5 27 6 18 105.2 17 31.2 25 124 99 12 24 8 M27 x 1.5 36 6 25 147 23 41.6 The dimensions of H/L type are the same.
Do not mount the product in locations where it is exposed to radiant heat. 5. Do not use in dusty locations or where water, oil, etc., splash on the equipment. 6.
KPGR08-12 12 d 10 18.5 24 41 29 50.5 25.7 9 KPQR10-12 KPGR10-12 Note 1) D indicates the maximum diameter.
KPGR08-12 12 d 10 18.5 24 41 29 50.5 25.7 9 KPQR10-12 KPGR10-12 Note 1) D indicates the maximum diameter.
To install/remove the product, use an appropriate wrench to tighten/loosen at the supplied nut on body B. 12. Mounting Do not apply torque at other points as the product may be damaged. Rotate body A manually for positioning after installation. Warning 1.