lPSMt Reconfiguring the operation mode, as well as the zero and span adjustments, are easy to do in the field. INSTALLATION A B c D Installation Transmission oin & Feed-back lever Fig. 1 SINGLE.ACTING ACTUATOR OPERATION ACTUATOR SIGNAL RANGE INSTALLATION STYLE (REFFIG. 1) OUT 1 OUT2 Direct ?
Do not attempt to disassemble tublng lrom fitting with vehicle air system under pressure, Glnflhd hhftilco ffiilt hr:iffi,bJn-|d$u[,ru,fl OHighly sistrrt OGradually corro&s (clpends on oporating conditions) Vl,lodelEl8ly .onodes (depends on opelating conditions) Not r6commnd6d br high concnlcrlions & )posur l coraoded Body Stud Guide Body Chuck Releass Bushing Collet Oring Packing SMC For
B)Whenusingacy|inderasaStop,useaguidetopreventside|oadsdirect|y on piston rod. 3) Do not damage exposed piston rod. such damage as scratching or excesssive scoring of exfosed piston rod may damage cylinder packing and cause air leakage.
When reassembling, do the opposite. Type 01T Wth Terminal Block Wirins . Remo\ junction cover of manifold to expose terminal block attached to the manilold block. Lead wires from solenoid valve are connected with the terminals on the upper side of the terminal block.
Olf a lubricant is used in the system, use turbine oil type f 1 (lSO VG32). lf lubricant has been used in the system, do not cease to lubricate as the original lubricant applied during manutacturing will have been washed away.
Nil S n Front nose mount Rear pivot mount Double end mount B C E Nil Without auto switch Auto switch Bore size 3/4" 1 1/16" 1 1/2" 2" 075 106 150 200 For the applicable auto switch model, refer to Best Pneumatics Stroke Hundredths of an inch (i.e. 06 = 0.06") Standard stroke Inches Specifications Specifications 075 (3/4") 200 (2") 106 (1 1/16") 150 (1 1/2") Bore size (in) Fluid Air Maximum
Do not insert the tube when the TKS is rotating, as the pawl may be damaged. KG KFG2 MS KKA KP LQ MQR T T IDK 489
VK300-82-2-01 VK300-82-2-02 VK300-82-2-07 VK300-82-4-51 VK300-82-4-06 VK300-82-3-05 VK300-82-3-53 1578
DOZ is not available. 2 9 Other Option Electrical entry 3 position closed center G: Grommet Lead wire length: 300 mm L: L plug connector With lead wire LN: L plug connector Without lead wire LO: L plug connector Without connector D: DIN terminal 3 3 position exhaust center 4 M: M plug connector With lead wire MN: M plug connector Without lead wire MO: M plug connector Without connector DO
(Rubber, Metal sliding parts: Fluorine coated) Non-greased specification H/DL L/LL Single plug With check valve Single socket Material Metal part: Stainless steel 304, Rubber material: Fluororubber (Special FKM) KC With male thread sealant Seal Note 1) Do not use the S couplers with a leak tester or for vacuum retention because they are not guaranteed for zero leakage.
Moisture control tube effective length Symbol 02 04 06 O.D. 2 mm 4 mm 6 mm Effective length 100 mm 200 mm Symbol 100 200 Dimensions Unit: mm Model Full length L Nominal effective length X L O.D. x I.D.
Do not plug or tighten it. Rc 1 1 2, 3 4, Rc 1 1 2, 3 4, (P port) (A port) Rc 1 1 2, 3 4, (R port) 1808
Also, do not use the filter when these chemicals are present in the atmosphere. 2
Do not apply an impact or large forces to a pad when adsorbing a workpiece. This will cause deformation, cracking and wear of the pad to be accelerated. The stiffening ribs, etc. should touch lightly, while staying within the pad skirt's deformation range. Positioning should be performed accurately. Especially in the case of small diameter pads. 6.
When piping and fittings, etc. are being screwed together, be certain that cutting chips from the pipe threads, sealing material, and other debris do not get inside the piping. Further, when pipe tape is used, leave 1.5 to 2 thread ridges exposed at the end of the pipe. 3. The unit should be mounted vertically. 4.
Body Size: 5000, Thread: N (NPT), Port Size: 06 (3/4), Option: None, Voltage: 5 (24 VDC), Lead Wire: DO (Type D, DIN Terminal w/o Connector), Surge Suppressor: None, Manual Override: B (Push-turn Locking Slotted Type), Flow Direction/Pressure Unit: Z (Name Plate and Pressure Gauge in Imperial Units)
Body Size: 5000, Thread: N (NPT), Port Size: 06 (3/4), Option: GS (Round Type Pressure Gauge, Silencer), Voltage: 5 (24 VDC), Lead Wire: DO (Type D, DIN Terminal w/o Connector), Surge Suppressor: None, Manual Override: B (Push-turn Locking Slotted Type), Flow Direction/Pressure Unit: Z (Name Plate and Pressure Gauge in Imperial Units)
Body Size: 5000, Thread: N (NPT), Port Size: 06 (3/4), Option: S (Silencer), Voltage: 5 (24 VDC), Lead Wire: DO (Type D, DIN Terminal w/o Connector), Surge Suppressor: None, Manual Override: B (Push-turn Locking Slotted Type), Flow Direction/Pressure Unit: Z (Name Plate and Pressure Gauge in Imperial Units)
Body Size: 5000, Thread: N (NPT), Port Size: 06 (3/4), Option: None, Voltage: 5 (24 VDC), Lead Wire: DO (Type D, DIN Terminal w/o Connector), Surge Suppressor: None, Manual Override: Non-locking Push Type, Flow Direction/Pressure Unit: Z (Name Plate and Pressure Gauge in Imperial Units)
Body Size: 5000, Thread: N (NPT), Port Size: 06 (3/4), Option: B (w/Bracket), Voltage: 5 (24 VDC), Lead Wire: DO (Type D, DIN Terminal w/o Connector), Surge Suppressor: None, Manual Override: B (Push-turn Locking Slotted Type), Flow Direction/Pressure Unit: Z (Name Plate and Pressure Gauge in Imperial Units)