Compact Manifold Regulator Do not drop or bump the product. Dropping or bumping while handling may cause damage to the product. 5. Lead wire dimensions Pressure Supply Warning Covering: 3.4 Insulator: 1.1 Conductor: 0.64 1. Do not use the switch with corrosive gas or liquid. Do not use the switch with corrosive gas or liquid. Such gas or fluid may cause damage to the switch. Operating Environment Warning 2.
The received message is deleted if the calculation result and received CRC do not match.
Do not use a screwdriver with a large grip or with a tip that does not fit into the trimmer groove because this could damage the groove.
An injury or failure can result. 3 Step Setting Mode Maintenance Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result.
HRR Series 3.1 Precautions wiring communication 3-1 HRX-OM-W004 Chapter 3 Serial communication 2 2 R D R D 3 3 S D S D 5 5 S G S G Master This product Do not connect any wire to other PIN numbers.
Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use. Bracket mounting Mount the bracket using the mounting screws supplied. The required tightening torque is 0.420.04 Nm.
Do not allow it to idle for a long time. If the pump is operated for a long time without any fluid inside or in a gas-fluid mixed state, the diaphragm may be damaged or the life may be shortened. Do not continue idling for 3 minutes or longer. 10.
Do not allow it to idle for a long time. If the pump is operated for a long time without any fluid inside or in a gas-fluid mixed state, the diaphragm may be damaged or the life may be shortened. Do not continue idling for 3 minutes or longer. 10.
Do not touch the leakage of fluid without care. If the fluid has high temperature or is chemical, the contact could result in burn and other injuries. 3) Disassembly Do not disassemble the pump. Caution 1) Quality of supplied air Mount the filter with filtration of approx. 0.01.
Please prepare according to 3.2 Connected explanation.In order to avoid malfunction, do not connect to any place other than those shown in 3.2 Connected explanation.
Do not use valves in atmospheres of corrosive gases, chemicals, salt water, water or steam, or where there is direct contact with same. 2. Do not use in an explosive atmosphere. 3. Do not use in locations subject to vibration or impact. 4. A protective cover, etc. should be used to shield valves from direct sunlight. 5.
Do not allow it to idle for a long time. If the pump is operated for a long time without any fluid inside or in a gas-fluid mixed state, the diaphragm may be damaged or the life may be shortened. Do not continue idling except for priming the pump. 5 11.
Do not use valves where there is direct contact with, or in atmospheres of, corrosive gases, chemicals, salt water, water or steam. 2. Do not use in an explosive atmosphere. 3. Do not use in locations subject to vibration or impact. Confirm the specifications for each series. 4. A protective cover should be used to shield valves from direct sunlight. 5.
Do not touch the cylinder during operation at a high speed and a high frequency. Use caution when handling a cylinder, which is running at a high speed and a high frequency, because the surface of a cylinder tube could get so hot enough as to cause you get burned. 2. Do not use the air cylinder as an air-hydro cylinder.
Do not use for intermediate stops while the cylinder is operating. This cylinder is designed for locking against inadvertent movement with the locking mechanism from a stationary condition. Do not perform intermediate stops while the cylinder is operating, as this may damage the cylinder, cause unlocking malfunction or shorten the service life. 3.
Do not touch the leakage of fluid without care. If the fluid has high temperature or is chemical, the contact could result in burn and other injuries. 3) Disassembly Do not disassemble the pump. Caution 1) Quality of supplied air Mount the filter with filtration of approx. 0.01.
When locked, do not apply impact loads, stroke vibration or rotational force, etc. This may damage the locking mechanism, shorten the service life or cause unlocking malfunction. 6. When an air cushion is used, operate the cylinder to the stroke end.
Prevention of electric shock and fire Do not operate the switch with wet hands. Also, do not operate the Thermoelectric Bath with water or fluid left on it. 2. Action in the case of error If any error such as abnormal sounds, smoke, or bad smell occurs, cut off the power at once, and stop supplying facility water.
Prevention of electric shocks and fire Do not operate the switch with wet hands. Also, do not operate the thermo-con when water is present on its exterior surface. 2. Action in the case of error If any error such as an abnormal sound, smoke, or bad odor occurs, cut off the power at once, and stop supplying and conveying fluid.
Do not cover the inlet and outlet vents.