Step Motor Driver （ Pulse input type ） Functional ground (When the driver is mounted, tighten screws and connect the grounding cable) (10) FG 18 - 3.3 Outside dimension diagram The outside view of this product is as shown in the diagram below: (1) Screw mount type (LECPA-) (2) DIN rail mount type (LECPAD-) 19 - 3.4 How to install (1) How to install The driver can be direct mounted using screws or mounted on a DIN rail.
(Refer to the installation manual) Connect frame-ground terminal (FG terminal) to the ground when using a switching power supply. Do not drop, hit or apply excessive shock (larger than 1000 m/s2) to the Auto switch. Otherwise it can result in damage to the Auto switch causing failure or malfunction. -5No.D-S-OMB0023-C Wiring Do not pull the lead wires.
Be sure to ground terminal FG when using a commercially available switch-mode power supply. Do not drop, hit or apply shock to the Pressure Sensor. Otherwise damage to the internal parts can result, causing malfunction. Do not pull the lead wire forcefully, not lift the product by pulling the lead wire.
contact (CLOSE During Alarm) Alarm Output Temperature Alarm a connector 6 7 8 9 6 contact (OPEN During Alarm) D-sub 9 pin (Pin type) 7 Temperature Alarm Fixed screw: M2.6 Common Temperature Alarm b 8 contact (CLOSE During Alarm) 3 Resistance Bulb Terminal A 8 1 4 Resistance Bulb Terminal B External temperature 5 Resistance Bulb Terminal B 15 9 sensor D-sub 15 pin (Socket type) connector 15 FG
Terminal block arrangement A-phase pulse input B-phase pulse input Bank 1 selection Bank 2 selection (UP pulse) (DOWN pulse) Sensor power Sensor power FG terminal Control input Sensor input Sensor input Reset input Hold input common common common output GND DC12V ..
(j) (d) FG (k) (l) (e) Mode switch Swich the mode between manual and auto. (m) Auto mode / Without alarm: Indicates the position number which is command by ON/OFF of IN0 to IN3 of the CN4 parallel I/O. (During command operation: Flashing / Instruction command completed: ON) Auto mode / With alarm: Indicates Alarm Group.
Ensure that the FG terminal is connected to ground when using a commercially available switchmode power supply. Do not drop, hit or apply excessive shock to the product. Otherwise damage to the internal parts of the product, solenoid valve and internal parts of the pressure switch can occur, causing malfunction.
contact (CLOSE During Alarm) 4,5 Unused Alarm Output connector 6 Temperature Alarm a contact (OPEN During Alarm) 7 Temperature Alarm Common 8 Temperature Alarm b contact (CLOSE During Alarm) 9 Unused 1,2 Unused External temperature sensor connector 3 Resistance Bulb Terminal A 4 Resistance Bulb Terminal B D-Sub 15pin (Socket) Fixed screw : M2.6 5 Resistance Bulb Terminal B 6-14 Unused 15 FG
Cover panels of the product should be opened only by qualified service technicians or qualified personnel. 15 FG Circulating fluidWater Circulating fluid flow rate3L/min Facility water flow rate10L/min Wetted materials SUS304 Circulating fluidEthylene glycol 20% Circulating fluid flow rate3L/min Facility water flow rate10L/min 2500 2500 Power supply Single phase AC100 to 240V(+/10%), Single
Ensure that the FG terminal is connected to ground when using a commercially available switch-mode power supply. Do not drop, hit or apply excessive shock to the product. Otherwise damage to the internal parts of the product, solenoid valve and internal parts of the pressure switch can occur, causing malfunction.
Be sure to ground terminal FG when using a commercially available switch-mode power supply. Do not drop, hit or apply shock to the Pressure switch. Otherwise damage to the internal parts can result, causing malfunction. Do not pull the lead wire forcefully, not lift the product by pulling the lead wire.
Use a protective cover. 15 FG Do not mount the product in a location where it is subject to strong 3.5 Model number of product vibrations and/or shock.
(g) (h) Frame ground (Tighten the bolt with the nut when mounting the (d) FG (i) controller. Connect the grounding wire.) (j) (e) Mode switch Swich the mode between manual and auto. (k) Auto mode / Without alarm: Indicates the position number which is instructed by ON/OFF of IN0 to IN3 of the CN4 parallel I/O.
r FG !1 !2 t y u i o !0 !1 !2 !3 !4 !5 !6 !7 !8 Mode swith Switch the mode between manual and auto. !3 !4 7-segment LED Stop position, the value set by i and alarm information are displayed. SET Set button Decide the settings or drive operation in Manual mode. Position selecting switch Assign the position to drive (1 to 14), and the origin position (15).
This fitting is available in 27 different body styles, with connection sizes from M5 to + R(PT), and tube sizes from 4mm OD to 12 mm OD., FITTING, EXTENDED MALE ELBOW, CONNECTORS, KG/KQ(X23) 1-TOUCH STAINLESS, FG, KQ(X23) 6MM, .07120 lb, Applicable tubing O.D. (mm)Connection threadsModel M5 type R type6R 1/4KGW06-02
Please contact us for the latest version.sales@ocaire.com, VALVE, AIR PILOT, BODY PT, VALVE, SY7000 SOL/VALVE, RUBBER SEAL, FG, SY7000 BODY PT 1/4, .48175 lb
Please contact us for the latest version.sales@ocaire.com, VALVE, DBL SOL, BODY PT, VALVE, SY7000 SOL/VALVE, RUBBER SEAL, FG, SY7000 BODY PT 1/4, 0.37699 lb
external pilot, pilot pressure range) 0.25 - 0.7MPa , Effective area mm 2 (Cv): body ported 10.6 (0.59); base mounted 12.6 (0.7) , Coil rated voltage: 3, 5, 6, 12, 24VDC; 100, 110, 200, 220VAC , Response time (0.5MPa) w/o indicator light andamp; surge voltage suppressor: 32ms or less , Ambient andamp; fluid temperature: 50 C, VALVE, DBL SOL, BODY PT, VALVE, SY7000 SOL/VALVE, RUBBER SEAL, FG
Accepts nylon and urethane tubes, Applicable for both vacuum and positive pressure applications, Release collar allows easy removal of tubing without damaging the tube, Maximum vacuum pressure of 1.0MPa, FITTING, MALE ELBOW, CONNECTORS, KQ2 FITTING, FG, KQ2 6MM, .02140 lb, Cylinder model sizeConnection threadApplicable tubingO.D.