JXCx-OMT0023 Screw size: M3 Tightening torque: 0.72 [N m] 11 10 11.
Reference data Units: mm IDH6 Jumper cord 7 6 5 4 3 1 PE Remote start/stop Fault-signal (N.O: Close at "Fault") Fault-signal (N.C: Open at "Fault") 1042 31 N 2 L Operation-signal (N.O) Ground Terminal screw: M3 Suitable wire: 1.25mm or more 2 244 Power supply Connector width: 6.5mm or less Detail of wiring 35 184 172 392 (Note) 15 80 223 321 3001 485 The type without built-in filter does
Piping to products When piping to a product, avoid mistakes regarding the supply port, etc. 1) When using SMCs M3 or M5 fittings, follow the procedures below to tighten them. Mounting Connection thread: M3 1. Operation manual Warning First, tighten by hand, then use a suitable wrench to tighten the hexagonal portion of the body an additional 1/4 turn.
Replacement procedure of shock absorber Loosen the hexagon socket head set screw (M3) at the piston rod by approximately one turn, and push down the lever. (See Fig. 11) Tool Hexagon wrench: Width across flats 1.5mm While pushing down the lever, remove the shock absorber and replace it with a new shock absorber. Tighten the hexagon socket head set screw (M3 x 0.5) of the piston rod.
Round head screw (M3 x 8), 4 pcs. EX600-ZMV2 (Specified for SY series) Enclosed parts: Round head screw (M4 x 6), 2 pcs. Round head screw (M3 x 8), 4 pcs. (2)End plate bracket EX600-ZMA2 Enclosed parts: Round head screw (M4 x 20), 1 pc. P tight screw (4 x 14), 2 pcs. EX600-ZMA3 (Specified for SY series) Enclosed parts: Round head screw (M4x20) with washer, 1 pc.
Round head screw (M3 x 8), 4 pcs. EX600-ZMV2 (Specified for SY series) Enclosed parts: Round head screw (M4 x 6), 2 pcs. Round head screw (M3 x 8), 4 pcs. (2)End plate bracket EX600-ZMA2 Enclosed parts: Round head screw (M4 x 20), 1 pc. P tight screw (4 x 14), 2 pcs. EX600-ZMA3 (Specified for SY series) Enclosed parts: Round head screw (M4 x 20) with washer, 1 pc.
(M3 screw) 5 Output connector Output signal interface for valve manifold. 6 LED display LED display to indicate the status of the SI unit. 2 7 Mounting hole Mounting hole for connection to the valve manifold. Accessories Hexagon socket head cap screw 2 pcs. M3 x 30 screw for connection to the valve manifold.
(M3 screw) 5 Output connector Output signal interface for valve manifold. 6 LED display LED display to indicate the status of the SI unit. 2 7 Mounting hole Mounting hole for connection to the valve manifold. Accessories Hexagon socket head cap screw 2 pcs. M3 x 30 screw for connection to the valve manifold.
(M3 screw) 5 Output connector Output signal interface for valve manifold. 6 LED and switch LED display to indicate the status of the SI unit 2 7 Mounting hole Mounting hole for connection to the valve manifold. Accessories Hexagon socket head cap screw 2 pcs. M3 x 30 screw for connection to the valve manifold.
Round head screw (M3 x 8) 4 pcs. EX600-ZMV2 (Specialized for the SY series) Enclosed parts: Round head screw (M4 x 6) 2 pcs. Round head screw (M3 x 8) 2 pcs. -103No.EX-OMU0028-D 3.
(M3 thread) (It is recommended to ground with resistance of 100 ohms or less) Accessories Hexagon socket head cap screw (M3 x 30): 2 pcs. Connects the SI unit and the valve manifold. Seal cap: 1 pc.
Match polarity between solenoid valve and SI unit output. -30No.EX-OMW0016-A Maintenance Replacement of the SI unit Remove the M3 hexagon screws from the SI unit and release the SI unit from the solenoid valve manifold. Replace the SI unit.
Round head screw (M3 x 8), 4 pcs. EX600-ZMV2 (Specified for SY series) Enclosed parts: Round head screw (M4 x 6), 2 pcs. Round head screw (M3 x 8), 4 pcs. (2)End plate bracket EX600-ZMA2 Enclosed parts: Round head screw (M4 x 20), 1 pc. P tight screw (4 x 14), 2 pcs. EX600-ZMA3 (Specified for SY series) Enclosed parts: Round head screw (M4 x 20) with washer, 1 pc.
Round head screw (M3 x 8), 4 pcs. EX600-ZMV2 (Specified for SY series) Enclosed parts: Round head screw (M4 x 6), 2 pcs. Round head screw (M3 x 8), 2 pcs. (2)End plate bracket EX600-ZMA2 Enclosed parts: Round head screw (M4 x 20), 1 pc. P tithe screw (4x14), 2 pcs. EX600-ZMA3 (Specified for SY series) Enclosed parts: Round head screw (M4 x 20) with washer, 1 pc.
JXC-OMT0002-C Part A Part B Holding screw M5X14 (2) Grounding Fit the grounding cable with crimped terminal between the M3 screw and shakeproof washer as shown below and tighten the screw. Shakeproof washer Grounding cable (with crimped terminal) M3 screw Caution The cable with crimped terminal and shakeproof washer must be prepared by the user.
Round head screw (M3 x 8) 4 pcs. EX600-ZMV2 (Specialized for the SY series) Enclosed parts: Round head screw (M4 x 6) 2 pcs. Round head screw (M3 x 8) 2 pcs. -114No.EX-OMW0006-D 3.
(Appropriate tightening torque: 0.4 to 0.6Nm) Part A Part B Holding screw M5X14 (2) Grounding Fit the grounding cable with crimped terminal between the M3 screw and shakeproof washer as shown below and tighten the screw. Shakeproof washer Grounding cable (with crimped terminal) M3 screw Caution The cable with crimped terminal and shakeproof washer must be prepared by the user.
Part number Description Note ZS-40-A Lead wire with M8 connector Length: 3 m ZS-42-A Bracket With mounting screws for PFMC7501/7102 (M3 x 5, 2 pcs.)
As the indicator LED protrudes from the switch unit, mounting the switch bracket above the LED may cause damage to it. (4) Insert the auto switch mounting screw (M3) included in accessories from the mounting hole of the auto switch mounting band, inserting the through hole of the switch bracket.
) (LEMC/LEMH/LEMHT) T slots Model Bolt Max. tightening Effective length torque [Nm] [mm] LEMC25 LEMH25 M3 0.63 45 LEMC32 LEMH32 M5 3.0 68 LEMHT25 M4 1.5 67 LEMHT32 M6 5.2 810 -39- effective length of it to enter from the bottom. 5.