CY1F Operate the piston within a range such that collision damage will not occur at the stroke end. 5. Consider a possible drop in operating pressure due to a power outage, etc. When a cylinder is used in a clamping mechanism, there is a danger of work pieces dropping if there is a decrease in clamping force due to a drop in circuit pressure caused by a power outage, etc.
EX500-AP050-S 5m Cables EX500-AP010-A 1m One end: molded M12 right angle connector. Other end: flying leads. EX500-AP050-A 5m Power supply PCA-1401804 1.5m One end: molded M12 straight connector. Other end: flying leads. PCA-1401805 3m Cable with Speedcon connector PCA-1401806 5m Table 6-2 Recommended Cables Note: More options are available.
A + A' A' w After piston seal H has passed air passage A, air is exhausted only through A'. The section marked with slanted lines becomes a cushion chamber, and an air cushion effect is achieved. A A' A' e When air is supplied for the piston extension, the check valve opens and the piston extends with no delay.
T-interface (T) M5 x 0.8, 1/8, 1/4, 3/8, 1/2 Factory mounting of a piping adapter on the AC models is available as a special order. Using a T-interface facilitates the redirection of air flow.
Caution Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. Warning 1.
MS-DOS is a registered trade mark of Microsoft Corporation. Pentium is a trade mark of Intel Corporation.
Displacement Use in a strong light source. Check that the Card Motor is not exposed to a strong light source such as direct sunlight. Install a light shielding plate as a cover.
A A A A A Speed Home position A B C Speed no. Time Two pattern combination example (A five point movement of absolute move A and incremental move B) Acceleration no.
A A A A A Speed Home position A B C Speed no. Time Two pattern combination example (A five point movement of absolute move A and incremental move B) Acceleration no.
* 7 A B-5 6 A A-5 * 9 B B-6 8 B A-6 3 (14.2) (2) 2 1 5.5 (18) (14) A1 B1 1 6 5 17.7 (3) 2 1 A6 B6 6.3 16 15 30.7 L (11) 59 - 15.3 [5m ] LE-CP--B(1) 2 A B-1 2 L A A-1 1 B B-2 6 B A-2 5 COM-A/COM B-3 3 COM-B/ A-3 4 3 Shield Vcc B-4 12 GND A-4 13 A B-5 7 A A-5 6 B B-6 9 B A-6 8 3 (4) + B-1 4 A-1 5 + B-3 1 A-3 2 8 (14.2) 1 2 (2) B1 A1 17.7 1 (14) A6 B6 5 6 10.2
As a result, the cylinder actuates. For this reason, when a workpiece must be lowered, use a cylinder with a built-in brake mechanism so that the cylinder will not actuate.
5 5m 5 40 32 25 40 32 25 10m 10m A A 1000 1000mm 1000mm 1000 12mm 12mm 16mm 16mm 20mm 20mm A A The length of motor, encoder and lock cables are same.
Body Size: 30 (03 Standard), Control: 0 (Meter-out), Rod and Applicable Tubing O.D.: ø8 - ø8, Lock Nut: J (Round Lock Nut)
Type: Speed Controller, Body Material: [Resin] Resin, Control Method: Meter-Out, Format: [Elbows] Plug-In Type, Environment, Applications: Standard, Knob Type: Resin, Lock Nut Option: Round Shape Lock Nut, Joint Type: Others, Applicable Tube O.D. mm(mm): 8, Body Size: 03 Standard
Also if the cable length exceeds 5m, the speed will be reduced 10% per 5m as the maximum. Note 3) A reference value for correcting an error in reciprocal operation. Note 4) Impact resistance:No malfunction occurred when the actuator was tested with a drop tester in both the stroke direction and perpendicular direction to the stroke.