Regulator Valve Select a model that is suitable for the desired air cleanliness by referring to SMC Best Pneumatics catalog. 2. Leakage voltage Take note that the leakage voltage will increase when a resistor is used in parallel with switching element or a C-R circuit (surge voltage suppressor) is used for protecting a switching device because of the passing leakage voltage through the C-R circuit.
Please contact SMC when the AC welding current exceeds 16000 A.
Suitable for slow operation of a rotary actuator. CC CC Integrate a converter and a valve unit in a compact configuration. Possible to select 4 types of valve units for applications. Possible to connect a converter and a valve unit independently. Wide range of series in terms of converter capacity and valve unit flow rate control capability.
Take note that the leakage voltage will increase when a resistor is used in parallel with switching element or a C-R circuit (surge voltage suppressor) is used for protecting a switching device because of the passing leakage voltage through the C-R circuit. The suppressor residual leakage voltage should be as follows. 5. Holding pressure (including vacuum).
When a cylinder is used in a clamping mechanism, there is a danger of work pieces dropping if there is a decrease in clamping force due to a drop in circuit pressure caused by a power outage, etc. Therefore, safety equipment should be installed to prevent damage to machinery and human injury.
Leakage voltage When C-R device (surge voltage suppressor) is used for the protection of switching device, the voltage leakage be increased by current passing through the C-R device. Therefore, select a circuit or device suitable to keep residual voltage leakage within the value described below.
Caution Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. Warning 1.
[Check valve] A check valve is a safety device intended to prevent reverse flow. The AP 64 is a unique design with only one moving part in the gas stream, an O-ring. It is a springless design, free of springs and poppets. [Vacuum generator] A venturi device that creates vacuum by flowing gas through a nozzle.
Ensure a stable power supply with no voltage surges. 3. Use a power supply suitable for the specifications of the product. 4. Be sure to connect the ground connection. 5. Grounsing should never be connected to a water line , gas line or lightning rod. 6. Multiple wiring is dangerous because it may lead to heat generation and cause a fine. 7.
Caution Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. Warning 1.
"Jumping" is a condition in which the cylinder operates without control at a speed that is higher than the control speed.
Supply the power from a stable source, free from surges. from a stable source, free from surges. 3.
: OFF (Retracted end) (4) Maximum Piston Rod Speed Setting: 0 (Default) Timing chart (STEP (A) to STEP (C)) Signal transition Input Signal name /Output STEP (A) STEP (B) STEP (C) PWR_DC24V 24 V (Power supply) 0 V E-STOP ON (Emergency stop) OFF CAL ON (Automatic mode) OFF 20mA Sig-in (+/-) (Analog signal input) 4mA 0mA 20mA (Set point) Pos-out (Analog position signal output) 4mA (Retracted
If additional tightening becomes ineffective, replace the fitting with a new product. 4. Check for the following during regular maintenance, and replace components as necessary. a) Scratches, gouges, abrasion, corrosion b) Leakage, refer to item 3 regarding taper thread leakage. c) Twisting, flattening or distortion of tubing d) Hardening, deterioration or softness of tubing 5.
When a cylinder is used in a clamping mechanism, there is a danger of work pieces dropping if there is a decrease in clamping force due to a drop in circuit pressure caused by a power outage, etc. Therefore, safety equipment should be installed to prevent damage to machinery and human injury.
Gear transmission Number of teeth = a 1.Find the moment of inertia IB for the rotation of shaft (B). 2.Next, IB is entered to find IA the moment of inertia for the rotation of shaft (A) as I = m 12 a + b b a IA = ( )IB Number of teeth = b 15 Technical Data/Moment of Inertia C Moment of Inertia Calculation Examples Rotational Axis at Random Point in Load 1 Example) When load is a rectangular
Closing the valve for initial pumping and the valve for main pumping When the initial and main pumping solenoid valves are de-energized, the valve S and M will return and start sealing. 9 XL-OMM0005-A 5 Dimensions 57.6 XLDV-25 (For AC) 55.4 (For DC) 2.2 8.5 C E B 1(P) D (KF flange) Fn G M5 1(P) SUP A M5 3(R) EXE H A XLDV-40160 C C E B 8.5 8.5 5.5 D (KF flange) Fd (K flange) M5 G Fn 1(P) SUP