The series is available in 12, 16, 20, 25, 32, 40, 50, 63, 80, and 100mm bore sizes. Non-rotating accuracy is 0.2 or less. Series CQM allows a workpiece to be mounted directly to the tooling plate.
The series is available in 12, 16, 20, 25, 32, 40, 50, 63, 80, and 100mm bore sizes. Non-rotating accuracy is 0.2 or less. Series CQM allows a workpiece to be mounted directly to the tooling plate.
Fieldbus system EtherNet/IP TM compatible SI Unit IO-Link Master Unit Mounting and Installation 30 Wiring 30 Specification 32 Specifications 32 Dimensions 33 IO-Link Master Unit Model Indication and How to Order 40 Summary of Product parts 40 Mounting and Installation 41 Wiring 41 LED Display 42 Specification 44 Specifications 44 Dimensions 45 Maintenance 46 Troubleshooting 47 Parameter Setting 58 Parameter definition and setting 58 -1No.EX-OMX1011 I/O Map 80
Order 16 Summary of Product parts 16 Mounting and Installation 17 Wiring 17 Setting and Adjustment 18 LED Display 23 Specifications 25 Dimensions 26 End Plate Model Indication and How to Order 27 Summary of Product parts 28 Mounting and Installation 30 Wiring 30 Specifications 32 Dimensions 33 Maintenance 42 Troubleshooting 44 Parameter Setting 55 Parameter definition and setting 55 I/O Map 80
Byte 80 Output 24 to 31 Total 77 bytes Total 81 bytes -83No.EX-OMA1023 Diagnostics By changing the diagnosis switch, the diagnostic data shown below is assigned to the input data of the I/O map.
The switch output load current (OUT1) has exceeded 80 mA. Turn off the power supply and remove the cause of the over current. Then supply the power again.
The switch output load current (OUT1) has exceeded 80 mA. Turn off the power supply and remove the cause of the over current. Then supply the power again. Do not use the product in a place where static electricity is a problem. Otherwise it can cause failure or malfunction of the system. Overcurrent error Function Setting The switch output load current (OUT2) has exceeded 80 mA.
Flow setting (3 step setting mode) Function setting (Function selection mode) Other functions [1000] 1000 L/min (PFMB7202) [F 1] OUT2 over current error The switch output (OUT2) load current has exceeded 80 mA. [ 10] 10 L/min (PFMB7201) [ 25] 25 L/min (PFMB7501) Do not use the product for flammable fluid. Fire or explosion can result.
OUT1 over current error The switch output (OUT1) load current has exceeded 80 mA. Turn the power OFF and remove the cause of the over current.
Insert the corresponding wire colour shown in the table into the pin number printed on the sensor connector, to the bottom. more than 20 mm Cover The switch output load current (OUT1) has exceeded 80 mA. [1ot ] Reversed output (OUT1) [1_n] Reversed output Turn off the power supply and remove the cause of the over current. Then supply the power again.
The identification code of the product is displayed. 4 Set value or 3 4 or 3 Set value Display instantaneous flow Display accumulated flow Output mode (OUT2) Reference condition 2 OUT1 over current error The switch output load current is more than 80 mA (OUT1). Turn the power off and remove the cause of the over current. Then turn the power on again.
Reduce the flow. 4 Set value or 3 4 Set value or 3 Caution Non-Reverse output Reverse output Accumulated pulse output mode Instantaneous output mode Accumulated output mode OUT1 over current error The switch output load current is more than 80 mA (OUT1). Turn the power off and remove the cause of the over current. Then turn the power on again.
Hysteresis Setting of hysteresis can prevent chattering. 5% of rated flow 1 41 mm Approx. 1 second Approx. 3 seconds (the output remains off for this period) 11/4 54 mm OUT2 over current error A load current of 80 mA or more is flowing to the switch output (OUT2). *: Display colour is linked to the setting of OUT1, and can not be selected.
[F 2] Setting of OUT2 OUT1: Black OUT1 over current error A load current of 80 mA or more is flowing to the switch output (OUT1). Turn the power off and remove the cause of the over current. Then turn the power on again.
In general, 80 to 100 mesh (150 to 180 m) filters are recommended. When transferring a coagulable liquid, take measures to prevent it from coagulating in the pump. Precautions to observe when transferring slurry Basically, it is not recommended to transfer slurry because this will result in seating failure and wearing of the check valve and accumulation of particles.
Ratio of discharge amount to fresh water (%) 100 90 80 70 60 50 40 30 20 10 0 1000 100 10 1 Viscosity (mPa s) mPas Silicone oil Lubricant Vegetable oil Water 60 to 80 1 6080 340 950 1500 3150 9800 Viscosity (mPa s) cp 0 100 1000 10 150 | 2650 45 | 2 3000 4500 Tomato juice Honey Medical barium Wooster source Cutting oil 4500 45 2000 to 3000 8 - 8.
Ratio of discharge amount to fresh water(%) 100 90 80 70 60 50 40 30 20 10 0 1000 100 10 1 Viscosity(mPa s) mPas Silicone oil Lubricant Vegetable oil Water 1 60 to 80 340 950 1500 3150 980 0 Viscosity (mPa s) 0 100 1000 10 Medical barium Cutting oil Tomato juice Honey Woosterource 4500 45 150 2000 to 3000 2650 8 - 8.
25 75 50 n 1 0 8 6 4 2 50 67.5 <69.5> L1 8 67.5 <69.5> 64.9 L2 4 x 9 (for M8 mounting) 3 port valve 2 port valve 64.9 50 8 10.5 Leakage detection port Pilot port C4: 4 One-touch fitting C6: 6 One-touch fitting G1/4 (RETURN port) G1/4 (IN port) 30 31 0.5 to 2 0.5 to 2 10 10 0.5 to 2 0.5 to 2 n-1 5 3 1 1 2 122.2 <124.2> 142.2 <144.2> 22.6 100 120 80 25 75 n 6 4 2 3 Gate valve Aluminum + hard
capacity(HRS030 W-20-(BJMT)) 9.4 Cooling capacity HRS Series 9-6 HRX-OM-R016 Chapter 9 Documents 9.6 Pump capacity 9.6.1 HRS030--20-(BJM) 0.3 Availavel area (Min. neccesary flow5L/min) Circulating fluid pressure[MPa] 20 Outlet60Hz 0.2 Pump head[m] 10 0.1 Outlet50Hz Return port 0.0 5 0 10 20 30 Circulating fluid flow[L/min] Fig. 9-7 Pump capacity(HRS030--20-(BJM)) 9.6.2 HRS030--20-T 0.8 80
HRR012/018-A-10-* 45 70 HRR012/018-A-20-* 61 80 HRR012/018-A-20-U 50 80 Model A B In the case of option Z, without bypass valve Fig. 9-1 Outline dimensions (HRR012/018-A-10/20-) 9.2 Outline dimensions HRR Series 9-6 HRX-OM-W002 Chapter 9 Documents 9.2.2 HRR012/018-W-10/20For Option Y(With feet and no Rack Mounting bracket), refer to [6.5 Option Y(With feet and no Rack Mounting bracket).