Slide Unit/Double Rod Type Series CX2 Slide Bearing: ø10, ø15, ø25 Note 1) 5 to 50 mm/s 5 to 40 mm/s 5 to 100 mm/s Note 1) Consult with SMC when the air-hydro type is mounted on a plate. Note 2) Consult with SMC when units are used at a low speed (10 mm/s or faster) (when intermediate stops are not required) since -XB13 (Low speed specification) is available. Note 3) When using the air-hydro type, use the double side hydro unit.
Toggle type air gripper Number of auto switches Nil S n 2 fingers Number of fingers 2 2 pcs. 1 pc. n pcs. Bore size 32 40 50 63 32 mm 40 mm 50 mm 63 mm Auto switch Nil Without auto switch (Built-in magnet) For the applicable auto switch model, refer to the table below.
PRODUCT SPECIFICATIONS S E R I E S I P 5 0 0 0 / I P 5 1 0 0 IP5000 (Linear) IP5100 (Rotary) SERIES 20 100 psi SUPPLY PRESSURE STROKE SENSITIVITY LINEARITY HYSTERESIS 0.4" 3.4" 60 100 degrees WITHIN 0.1% F.S. WITHIN 0.5% F.S. WITHIN 1% F.S. WITHIN 0.75% F.S. WITHIN 1% F.S. WITHIN 2% F.S. WITHIN 0.5% F.S.
Mount switches in locations without vibration (98m/s or less) or impact (490m/s or less). 3. Do not use in an area where surges are generated. When there are units (solenoid type lifters, high frequency induction furnaces, motors, etc.) which generate a large amount of surge in the area around switches, this may cause deterioration or damage to the switch.
.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com 0.03 s or less 0.03 s or less 0.05 s or less 0.05 s or less Response time Hysteresis 3% F .S. IR Repeatability 3% F .S. VEX Sensitivity 0.5% F .S.
Response time (With anti-chattering function) Output short circuit protection Display 2% F .S. 1 digit or less (at ambient temperature of 25 3C) Green LED (OUT1: Lights when ON), Red LED (OUT2: Lights when ON) Output voltage: 1 to 5 V 5% F.S. or less (in rated pressure range) Linearity: 1% F .S. or less Output impedance: Approx. 1 k No-voltage input (Reed or solid state), input 5 ms or more
L, Z S L, Z S Note ) Thread PB 1 32A 40A 50A AC Flange DC Note) Surge voltage suppressor is attached in the middle of lead wire.
Z S L, Z S Note ) PAX 1 1 4 1 2 PB AC Ordering example (Example) Series VXR21, Rc 3/4, 24 VDC, Conduit terminal (Part no.)
Gap too small Green 2 a Place the gap gauge on the detection nozzle for precise adjustment. s Confirm applied air pressure.
Example: VEX1300-03 G36-4-01 (Constructive symbol) 5.1-1 VEX1 How to Order 1 03 D 3 1 0 B VEX Regulator valve B Bracket Option F Foot (Only VEX110) G Gauge When specifying more than one option, combine symbols in alphabetical order. 0 Air operated Operating style 1 External pilot solenoid None Indicator light and surge voltage suppressor S Surge voltage suppressor Z Indicator light and
SMC Corporation of America (Detroit) 2990 Technology Drive Rochester Hills, MI 48309 TEL: (248) 299-0202 FAX: (248) 293-3 w w w . s m c u s a . c o m SMC CORPORATION OF AMERICA U.S. HEADQUARTERS 3011 N. FRANKLIN ROAD INDIANAPOLIS INDIANA 46226
Calculation ZX ZR : Lifting force (N) : Stable vacuum pressure (kPa) : Pad area (cm2) : Factor of safety: Horizontal pad contact : 4 (dynamic) Vertical pad contact : 8 (dynamic) W P S t Pad ZM W = P x S x 0.1 x 1 t W ZH W ZU Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
@w, s Bore Siee Noaulo swjtch builtjn (hjglr magnelic Add L and Z at the end of part numberlor 3m and sfi, respectively. "ALrto switch detail: see pgs. 10-11.
rated pressure range, Ambient temperature 25 3C) Linearity 1% F .S. or less Repeatability 1% F .S. or less Power supply voltage effect 1% F .S. or less based on the analog output at 18 V ranging from 12 to 24 VDC Enclosure IP40 Temperature range 0 to 50C; Stored: 10 to 70C (No freezing or condensation) Resistance Withstand voltage 1000 VAC, 50/60Hz for 1 minute between external terminals
Make sure to connect a speed controller and adjust it to a speed of 500 mm/s or less to operate the cylinder.
Valve model Type of actuation Port size 1 4/2 (P A/B) Flow characteristics Note 2) Note 3) Effective area mm2 4/2 5/3 (A/B EA/EB) Weight (g) Pilot port size Cv C [dm3/ (s bar)] b Cv C [dm3/ (s bar)] b Grommet Single Double Closed center Exhaust center Pressure center Single Double Closed center Exhaust center Pressure center Single Double Closed center Exhaust center Pressure center 48
IR Repeatability 3% F .S. VEX Sensitivity 0.5% F .S.
5.26 AIR PREPARATION HIGH FLOW SERIES LUBRICATOR SERIES (N)AL Port Sizes 1 12~2 Atomizes Lubricant into fine particles at a uniform rate Drip Rate easily monitored with Sight Dome Can be filled under pressure Bowl Guard Standard Damper precludes oil flooding S Y M B O L S H O W T O O R D E R L U B R I C AT O R S E R I E S NAL NAL800-N12 (1 14 NPT) NAL800-N14 (1 12 NPT) NAL900-N20 (2 NPT)
CDA2 B 50 200 X1184 B31J S With built-in special magnet Number of auto switches Cylinder stroke Description 2 pcs. 1 pc.
Note 1) 5 to 50 mm/s 5 to 40 mm/s 5 to 100 mm/s Note 1) Consult with SMC when the air-hydro type is mounted on a plate. Note 2) Consult with SMC when units are used at a low speed (10 mm/s or faster) (when intermediate stops are not required) since -XB13 (Low speed specification) is available. Note 3) When using the air-hydro type, use the double side hydro unit.