AC Servo Motor Driver (Pulse input type/Positioning type) (If you do not cycle the power, it does not register the data in the driver.) Note2) Selected Items Write: Writes the parameter values of the corresponding frame to the driver. Single Axis Write: Writes all of the parameters to the driver. Note3) Do not change For manufacturer setting parameters.
IEC 60204-1: Safety of machinery -Electrical equipment of Do not use in an explosive atmosphere. Do not expose to direct sunlight. Use a suitable protective cover. Do not install in a location subject to vibration or impact. Check the Maintenance of pneumatic systems should be performed only by qualified personnel.
Do not use compressed air which contains chemicals, organic solvents or corrosive gases. Do not use compressed air containing chemicals, organic solvents, salt or corrosive gases, as this can cause damage and reduced performance, etc. 3. Operating pressure range The operating pressure range is determined by the equipment being used.
Do not use compressed air which contains chemicals, organic solvents or corrosive gases. Do not use compressed air containing chemicals, organic solvents, salt or corrosive gases, as this can cause damage and reduced performance, etc. 3. Operating pressure range The operating pressure range is determined by the equipment being used.
When a pressure gauge is mounted to the regulator, please do not exceed the maximum display pressure. It may lead to a malfunction.
Caution As a jig is required for bore size 6, do not disassemble when replacing seals etc. If overhaul is required, contact SMC Sales Office.
Do not mount the product in locations where it is exposed to radiant heat. 5. Do not use in an environment where flammable gas or explosive gas exists. Usage may cause a fire or explosion. The products do not have an explosion proof construction. 6. If it is used in an environment where there is possible contact with oil, weld spatter, etc., exercise preventive measures. 7.
Do not service machinery/equipment or attempt to remove component until safety is confirmed. 1) Inspection and maintenance of machinery/equipment should only be performed after confirmation of safe locked-out control positions. 4-17-4
Make sure that dust and/or other foreign materials do not enter the valve from the unused port (e.g. exhaust port). Also, since there is a breathing port for the armature in the manual override part, do not allow accumulation of dust and/or other foreign materials to block bleed port.
How to Order KQ2 H 05 S 02 With thread seal One-touch fittings Nil Without seal S With thread seal Applicable tubing O.D.
x 1 m) AS3301F-02-08/AN110-01 Speed controller/Silencer It is when the cylinder is extending that is meter-out controlled by speed controller which is directly connected with cylinder, and its needle valve with being fully open.
wire length 300 mm) Grommet (Lead wire length 600 mm) DIN terminal DIN terminal (Without connector) Nil Without sub-plate H D DO 2 01 1 8 1 8 Base mounted 02 1 4 1 4 Caution Refer to front matters 58 and 59 for Safety Instructions and pages 3 to 7 for 3/4/5 Port Solenoid Valve Precautions.
Do not connect the white wire of the sensor to . View A Terminal block number 4 3 2 1 1 2 3 4 5 6 7 8 8 7 6 5 20 For Water Digital Flow Switch/High Temperature Fluid Type Series PF2W Refer to www.poweraire.com for details of products compatible with overseas standards.
Do not indicate suffix N for no lead wire on D-A3/A44/G39/K39 models.
The received message is deleted if the calculation result and received LRC do not match. Consecutive 8 bits of the message are added, and the result without carry (overflow) is converted to 2's complement.
Do not use in an atmosphere having corrosive gases, chemicals, sea water, water, water steam, or where there is direct contact with any of these . 2. Do not use in an environment where flammable gas or explosive gas exists. Usage may cause a fire or explosion. The products do not have an explosion proof construction. 3. Do not use in a place subject to heavy vibration and/or shock. 4.
Material: Carbon steel (Nickel plated) With end lock 12 Width across flats 14 3 D-X Individual -X 124.5 + Stroke 145.5 + Stroke 245 Series MTS Dimensions: 32 Note) Spline rods width across flats have nothing to do with the position of the body mounting face.
Do not operate in an atmosphere containing flammable or explosive gases. Fire or an explosion can result. This product is not designed to be explosion proof. Do not use the product in a place where static electricity is a problem. Otherwise it can cause failure or malfunction of the system.