I D 00 Without subplate 1% 0.5% + -0.5% M5 M5 0.007 00 Without subplate B M5 M5 0.28 01 18 0.41 2.5% 1% + -1% Base Mounted Type 00 Without subplate 2 01 18 0.9 02 14 1.4 00 Without subplate 02 14 2.0 3% 1.5% + -1% 4 03 38 3.3 04 12 3.9 A M5 M5 0.28 1 01 18 0.9 02 14 1.4 2.5% 1% + -1% Wiring: The use of three-core screened cable is strongly recommended with the screen earthed at the end away
Binary Output 1 OFF OFF 2 ON OFF 31 point preset output is possible without bank switching, by means of binary system output from a 5 point output terminal.
(M3 screw) 5 Output connector Output signal interface for valve manifold. 6 LED and switch LED display to indicate the status of the SI unit. 2 Switches for setting of node address and operating mode. 2 7 Mounting hole Mounting hole for connection to the valve manifold. Accessories Hexagon socket head cap screw 2 pcs. M3 x 30 screw for connection to the valve manifold.
Mounting with brackets Mount a bracket to the using two M3 x 5L mounting screws and install on piping with a hexagon socket cap screws. The switch can be installed horizontally depending on the installation location. Mounting screw M3 x 5L Atmospheric release port To a safe place with no water or dust The tightening torque for bracket mounting screw should be 0.98Nm or less.
Series AS-FG Speed Controller with One-touch Fittin Stainless Series. 5 5 6 7 9 11 11 11 11 12 13 13 13 15 15 16 16 16 17 17 18 19 21 22 22 23 24 25 27 27 27 29 30 31 31 31 32 34 35 35 35 36 36 37 37 37 38 38 39 39 39 41 42 43 43 43 44 45 46 46 Specifications. How to Order . Construction. Dimensions . Series AS-FG Speed Controller with One-touch Fittings Stainless Series In-line Type.
Manufacturer M4 x 0.7 M3 x 0.5 Thread size 32.5 21.5 Effective thread length (mm) 8 6 Quantity 2 4 P.C.D. 46 45 Motor mounting area When mounting a coupling on the motor, mount it within the dimensional range shown on the left. A A B Section BB P.C.D.
(M3 thread) (It is recommended to ground with resistance of 100 ohms or less) Accessories Hexagon socket head cap screw (M3 x 30): 2 pcs. Connects the SI unit and the valve manifold. Seal cap: 1 pc.
(M3 screw) 5 Output connector Output signal interface for valve manifold. 6 LED display LED display to indicate the status of the SI unit. 2 7 Mounting hole Mounting hole for connection to the valve manifold. Accessories Hexagon socket head cap screw 2 pcs. M3 x 30 screw for connection to the valve manifold.
Max. air flow rate (m3/min (ANR)) JIS Symbol P . 14-20-55 Inlet pressure (MPa) Caution Be sure to read before handling.
Input No. assignment The inputs of the Input block are assigned from the SI unit side Input block in the order 0,1,2maximum of 31. 2 Power supply connector Supplies power to the solenoid valve, the Output block, SI unit and the Input block. 3 Input block connector Connects the Input block.
Warranty period and guaranteed range The guaranteed period covers the period which finishes the earliest among 2 million operating cycles [with our durability test conditions], 18 months after shipping from us, and 12 months after starting the use of the product at your place or your customers place.
Definition and terminology 11 Mounting and Installation 14 Installation 14 Piping 16 Wiring 17 Pressure Setting 19 Measurement mode 19 Function Setting 21 Function selection mode 21 Default setting 21 F0 Units selection function 23 F1 Setting of OUT1 24 F2 Setting of OUT2 27 F3 Response time 27 F4 Analogue output / Auto-shift input 28 F5 Display resolution 30 F7 Fine adjustment of display value 31
Without flow adjustment valve (using ZS-33-M) With flow adjustment valve (using ZS-33-MS) Install the product (with bracket) using the M3 screws (4 pcs.). Bracket thickness is approximately 1.2 mm. Refer to the dimension drawing of the bracket (page 71) for mounting hole dimensions.
Offset 3: Power supply connector Supplies power to the solenoid valve, the Output block, SI unit and the Input block. 2 30 28 26 24 22 16 0 4 6 4 2 0 6 20 18 4 2 0 4 0 4 0 Input No. Bit No.
Step 7 Reassembly of bonnet assembly (No.2) 3 Bolt 1 2 4 Bonnet assembly Pilot port Bolt size, Tool, Tightening torque of bolt (Nm) valve Bolt size Hex Tightening size wrench torque XLF-16 M3 3 0.7 -25 M5 4 1.5 -40 M6 5 2.5 -50 M8 6 6.1 -63 M10 8 15 -80 Body Supply air pressure of 0.4MPa (G) to the pilot port.
Dimensions (page 31) for necessary space. Piping Warning: 1) Before piping, perform flushing or cleaning of the piping, etc. to remove any cutting chips, cutting oil, solid foreign matter, etc. from the piping.
M5 7 MACM6 X114 118 125 125 97 113 33.8 53 28 33.3 30 43 X115 59 6 98 60 X116 57 4 60 MACM10 X114 185 197 198 11 152 182 18 53.8 77 31 24 13 0 53.3 50 70 X115 83 6 108 X116 81 4 5 Centering Unit MACM Series Dimensions P: Port side photo sensor mounted type B: Port back side photo sensor mounted type Mounted example of EE-SX671 made by OMRON P: Port side photo sensor mounted type 4 19
. 2017 SMC Corporation All Rights Reserved 18 XL-OMV0016
ZL-OM00801 Revision history 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021 JAPAN Tel: + 81 3 5207 8249 Fax: +81 3 5298 5362 URL http://www.smcworld.com This manual is subject to change without prior notice. 2010 SMC Corporation All Rights Reserved 31 -
Model AMD450 AMD550 AMD650 AMD850 AMD150 AMD250 AMD350 Rated flow (l/min (ANR))(1) 2000 3500 6000 12000 200 500 1000 Port size (Nominal size B) 1/8, 1/4, 3/8 1/4, 3/8, 1/2 3/8, 1/2, 3/4 1/2, 3/4, 1 31/2, 1 1, 11/2 11/2, 2 Weight (kg) 0.38 0.55 0.9 1.4 2.1 4.2 10.5 Standing Style/Model Model AMD1000 Rated flow (l/min(ANR)) 8000 AMD800 24000 AMD900 40 Port size (Nominal size B) 2B Flange 2B