SYJ300/500/700 Type 40/Type 41 How to Order SS3YJ7 40 05 01 Applicable solenoid valve SYJ714SYJ714MSYJ724SYJ724MApplicable blanking plate assembly SYJ700-10-2A R port 1/4 R port 1/8 P, R port thread type Manifold type Stations 40 41 Type 40 Type 41 Nil Rc G NPT NPTF 2 stations : 20 stations 02 : 20 A A F N T A A 01 1/8 A port size P port 1/8 P port 1/4 Courtesy of Steven Engineering, Inc.-230 Ryan Way,
When a filter element is used repeatedly, clean it with air blow or wash it with a neutral detergent. (For 40 m, For 80 m) Check the condition of the element and replace the element with a new one when the specifications are not satisfied.
When the dryer is drawing in high temperature air that is discharged from an air compressor or other dryer. The ventilation port is obstructed by a wall or clogged with dust. The auto drain may not function properly, depending on the quality of the compressed air. Check the operation once a day.
auto switch when mounting a housing of 10.
The cushion effect (smooth start-up, soft stop) cannot be obtained in an intermediate stop or a return from an intermediate stop using an external stopper, etc.
Unpacking the sealed package Since the filter and element are sealed in an antistatic double bag, the inner package should be unpacked in a clean atmosphere (such as a clean room). 316
Therefore, operate with a silencer (SMC Series AN) mounted on the exhaust port (EXH port). The connection is Rc 1/2. 1. When remounting the valve guide after removing it for maintenance, use a tightening torque of no more than 0.6 Nm. Since the valve guide on this product is made of resin, there is a danger of damage if tightened with a torque exceeding the prescribed value.
Compact lock unit is light weight and saves space Overall length has been reduced by using an independent brake cylinder (15% compared to P/A products).
Smooth operation and longer life from an oil containing slide bearing. Rotary seal A special rotary seal minimizes friction while providing an excellent seal.
Parts cannot be shipped separately. 1937 Series VHS20/30/40/50 Dimensions VHS20/30 VHS40/40-06/50 10 I EXH. 10 G F H I SUP. E X H . F G H SMC P . U S C E Padlock mounting position D C Padlock mounting position D SUP. SUP A B A B IN OUT IN OUT 2 1 3 EXH. EXH.
As a rough guide, thighten the screw an additional 90o after feeling a tight resistance. Switch reset position(OFF) MHZ2 MHZJ2 Protrusion of Auto Switch from Edge of Body MHQ The maximum protrusion of an auto switch (when fingers are fully open) from the edge of the body is shown in the table below. Use the table as a guideline for mounting.
If using the product in an interlocking circuit: Provide a double interlocking system, for example a mechanical system. Check the product regularly for proper operation. Otherwise malfunction can result, causing an accident.
Use a tube with an O.D. of 10 mm and a length of 5 m or less for the piping of the auto drain. Before and after piping is connected, it should be thoroughly blown out with air (flushing) or washed to remove chips, cutting oil, and other debris from inside the pipe. 5. Provide a design that prevents back pressure and backflow. 3.
Time Delay A Knob Actuated before time set Time delay (sec) B Signal pressure (MPa) Example) A is the point, which is set by the input signal pressure 0.25 MPa, with a delay time of 60 sec. With the same status, if the input signal pressure is increased to 0.8 MPa, the delay time varies to the B point ( 40 sec). Actuated after time set Piping Length vs.
Series REAL Size: 10, 15, 20, 25, 32, 40 To ensure a permanent path. When smoother operation is required, even with an eccentric load. Stable operation is possible even with an eccentric load, through the use of a ball bushing. Series REAH Size: 10, 15, 20, 25, 32 The use of a linear guide makes possible a large load, large moment and high precision.
Lead Wire Clamp/Lead Wire Cap (Option) CNS Series Lead wire clamp LC-01 Lead wire cap LP-01 ML1C CLS Lead Wire Clamp/Lead Wire Cap (Option) (mm) CLQ 25 32 40 Mounting position Series Series Lead wire clamp Lead wire cap A 124.8 148.8 173.8 LP-01 ML1C LC-01 ML1C MLGP B 113.2 137.2 162.2 25 32 40 Series Mounting position RLQ ML1C 177.5 A 128.5 152.5 B 123.5 147.5 172.5 MLU Operating Range Minimum
Lead Wire Clamp/Lead Wire Cap (Option) CNS Series Lead wire clamp LC-01 Lead wire cap LP-01 ML1C CLS Lead Wire Clamp/Lead Wire Cap (Option) (mm) CLQ 25 32 40 Mounting position Series Series Lead wire clamp Lead wire cap A 124.8 148.8 173.8 LP-01 ML1C LC-01 ML1C MLGP B 113.2 137.2 162.2 25 32 40 Series Mounting position RLQ ML1C 177.5 A 128.5 152.5 B 123.5 147.5 172.5 MLU Operating Range Minimum
Temperature Data A or B = Series IDUS: Data A Series IDFS: Data B Air pressure Data C = 2 Calculate corrected air flow by using A or B and C. Corrected air flow = (Air flow) (Data A x Data C) Corrected air flow = (Air flow) (Data B x Data C) 3 Select a model having an air flow capacity that is higher than the corrected air flow.
When stopping a load directly connected to the cylinder at an intermediate position: Apply the operating range in the catalog only in these cases where the stopper cylinder is used to stop pallets on a conveyor belt. When using the stopper cylinder to stop loads directly connected to a cylinder or some other equipment, a lateral load is applied as the cylinder thrust.
1 Stopper Cylinder (Adjustable mounting height) 40, 50 Series RSQ Series RSG (Fixed mounting height) 12, 16, 20, 32, 40, 50 Realize labor saving and automation of conveyor line A through-hole style and a both ends tapped style are available.