MHR2/MDHR2, MHR3/MDHR3 Rotary Actuated Air Gripper (2 Finger) (3 Finger) 3 o @1 @0 !1 !0 !2 r w i e !5 !9 y u t MDHR3 !4 !3 q !1 @0 @1 w o e i MHZ2 !5 MHZJ2 MHQ r !7 !6 t !0 !8 !2 i !9 y u MHL2 Component Parts Component Parts MHR No. !2 !3 !4 !5 !6 !7 !8 !
R Q2 B P C F(h9) D G1 G2 J K L M N Q1 E(g6) Q3 Model A 90 180 270 M5 M3 CRB1BW10-lS CRB1BW10-lSE CRB1BW15-lS CRB1BW15-lSE CRB1BW20-lS CRB1BW20-lSE CRB1BW30-lS CRB1BW30-lSE 3.4 (5.5) 5 8.5 5 11 9 14 10 15.5 25 9.5 25 10 25 13 25 14 M3 (6) 0 0.036 15 24 8 0.004 0.012 9 14 3 1 5 9 0.5 29 4 M3 M3 (5) M5 M3 3.4 (6) M3 (10) 0.004 0.012 0 0.043 20 29 9 12 18 5 4 1.5 6 10 0.5 34 M3 M4 (7.5) 4.5
Selection procedure 1. First find the ratio of the discharge rate for fresh water when viscosity is 100mPas from the graph at the left. It is determined to be 45%. 2. Next, in the required specification example the viscosity is 100mPas and the discharge rate is 2.7l/min.
However, there is no problem in terms of contact output, when an output signal exceeds 1 mA or more.
Rc 1 4 1 4 1 4 NPT G Y F02 Body option 1 0 Internal pilot type External pilot type Twist selector (2 position) Key selector (2 position) Note 1) When selecting the flush type, it is not necessary to select the suffix for the actuator.
1 For the remote type monitor unit, only the front side is IP65 compliant.
5.5 2.5 5.5 3 1 1 6 10 15 20 25 32 20.5 27.5 38 50 50 60 4.5 7.5 4.5 7 9 9 Note 1) Negative figures in the table D indicate how much the load wires protrude from the cylinder body.
returned when the following request message is received. 1) When unspecified function code is used. 2) An address out of range is specified. 3) The data field is not normal.
t 8 Embedded pressure gauge is a standard teature (HNBB) lmproved relief '1.
HHH is 6 displayed. (1) Reset applied pressure (1) Check that the pressure is not to a level within the set pressure range.
Load Load Switch 1 Switch 1 Blue [Black] Blue [Black] Brown [Red] Brown [Red] Switch 2 Switch 2 Blue [Black] Blue [Black] Internal voltage drop Power supply voltage Leakage current Load impedance Load voltage at OFF = x 2 pcs. x = 1mA x 2 pcs. x 3k = 6V = 24V 4V x 2 pcs. = 16V Example: Power supply is 24VDC Internal voltage drop in switch is 4V Example: Load impedance is 3k Leakage current
Symbol In the symbol ( ), when the valve is closed, flow is blocked from port 1 to port 2. However, if the pressure in port 2 is higher than port 1, the valve will not be able to block the fluid and it will flow from port 2 to port 1. 1.
HHH is 6 displayed. (1) Reset applied pressure (1) Check that the pressure is not to a level within the set pressure range.
An over current Incorrect internal data processing of the product (Er0, 4, 6, 7, 8 or 9) (1) Check if there is noise interference error (Er1, 2) is displayed. (such as static electricity. (2) Check if the power supply voltage System error is in the range 24 VDC 10%. (Er0, 4, 6, 7, 8 or 9) is displayed. (2) Supply power in the range 24 VDC 10%.
The brown lead wire is (+) and the blue lead wire is (). 1) If connections are reversed, a switch will operate, however, the light emitting diode will not light up. Also note that a current greater than that specified will damage a light emitting diode and it will no longer operate. Applicable models: D-C73, C73C D-B53, B54 1. Do not drop or bump. 1.
MY1 Air cushion is standard Impact absorption is possible at the highspeed stroke end.
When the product is shipped, the cushion needle of the cylinder is opened by 1-2 rotations from fully closed and then the lock nut is tightened.
VS7-8-FG-D-3M 1 pc. (Third station of manifold where 1 piece of VS7-8-FG-D-3M is added to the basic unit of VER2000-A and VS7-8-FG-S-3N.) AL Dimensions DXT334-X72-04R-04U L side U side D side Exhaust port R side Rc 1/2 supply port (L side) 2-Rc 1/2, Output port 14-9-23
When the signal is turned on, discharge stops. 9 External switch signal 2 Input Input Light blue When the signal is turned on, discharge stops.
(A) 2 Manual override 1 None 1 (P) B (1) Locking style (Slotted style) Note) Consult SMC if N.O. type is desired Note 1) Only normally closed DIN connector in-line style is applicable.