0.55 In that case, loosen the screw with washer (3e) and place a lead wire (3d) into the bracket, and then tighten it once again. b Maximum size of crimped terminal (9) is up to 1.25 mm2 3.5 when O terminal.
Be careful not to exchange the power cable (brown) with the output cable (black). 10-20-37 38 Solid State Switch Direct Mounting Style D-Y59 /D-Y69 /D-Y7P(V) A B A B For details about certified products conforming to international standards, visit us at www.smcworld.com.
19 19 19 Weight kg 0.5 0.6 0.7 Weight kg 0.5 0.6 0.7 NAAMS code ACA206M ACA207M ACA208M NAAMS code ACA216M ACA217M ACA218M A B C D E F G H I A B C D E F G H I Part no.
C D E F H N-OT 0 1 2 3 4 5 6 Reverse Run Prohibited Pn50B.0 7 8 L /N-OT 0 A B C D E F L /P-CL 0 1 2 3 4 5 6 Forward External Torque Limit Pn50B.2 8 7 H P-CL 9 A B C D E F L /N-CL 0 1 2 3 4 5 6 Reserve External Torque Limit Pn50B.3 8 7 H N-CL 9 A B C D E F L /DEC 0 1 2 3 4 5 6 Homing Deceleration LS Pn511.0 8 7 H DEC 9 A B C D E F L EXT1 * * * * 4 5 6 External Latch Signal 1 Pn511.1 7 8 H
port size (inch) A, B port size (metric) spaEleyonamanr'od Manifold D-sub Connector .
AREA A position 2 The AREA signal is output commonly for the ranges set for both the AREA A and AREA B. AREA B Set as AREA 1 AREA 2. position 1 AREA B position 2 48 - Data (Saved data) Data is sent as hexadecimal numbers.
A B A B A B How to Mount and Move the Auto Switch How to Mount and Move the Auto Switch Flat head watchmakers screwdriver Auto switch mounting screw (M2.5 x 4 l) Accessory Auto switch mounting nut M2.5 x 4 l 5 to 6 Note) When tightening an auto switch mounting screw, use a watchmakers screwdriver with a grip diameter of 5 to 6 mm.
B) Under the above conditions, adjust shim so that the space between the workpiece and the clamping block is about 0 mm. Theoretically there is no clamping force for holding a workpiece under this condition. C) In order to generate clamping force from the state described in step B, insert additional shim.
Position 2 The AREA signal is output for both the AREA A and AREA B set configuration. AREA B Set as AREA 1AREA 2. Position 1 AREA B Position 2 21 (2) Step Data Save Command "EU" Details Use after executing Step Data setting comand "EE".
Auto switch a c b d Proper Mounting Position (mm) D-Z7/Z80 D-Y59/Y7P D-Y69/Y7PV D-Y7W D-Y7WV Auto switch model D-M9 D-M9V D-M9W D-M9WV D-A9 D-A9V Proper Mounting Position (mm) A B A 15 19.5 24.5 B A 14 18.5 23.5 B Bore size 63 80 100 a b 14 18 17 c 20 24 23 d Auto switch model 15 18 22.5 19 23.5 28.5 11 14 18.5 10 13 17.5 D-A9 D-M9 D-M9W 2 6 5 8 12 11 Note) Adjust the auto switch after confirming
. 2016 SMC Corporation All Rights Reserved VP4*50*-OMC0001-B
In that case, loosen the screw (3f) and place a lead wire into the bracket (3d), and then tighten it once again. b) The maximum size for the round terminal (9) is 1.25 mm2 3.5 and for the Y terminal is 1.25 mm2 4. c) Cable (8) outside diameter: 6 to 12 mm Note) For the one with outside diameter ranged between 9 to 12 remove the inside parts of the rubber seal (7) before using. 3.
. 2018 SMC Corporation All Rights Reserved VT317-OMH0002-B
Analog Output Flow/Analog output Output A B C Voltage output 1 V 1.1 V 5 V Current output 4 mA 4.4 mA 20 mA C Model Rated flow [L/min] Minimum Maximum LFE1 0.5 20 LFE2 2.5 100 LFE3 5 200 B A Outside the range 0 Min.
A B For details about certified products conforming to international standards, visit us at www.smcworld.com.
A B For details about certified products conforming to international standards, visit us at www.smcworld.com.
A B For details about certified products conforming to international standards, visit us at www.smcworld.com.