Made to Order CQ2 series Stroke S2 Part no. denotation B Stroke S1 Part no. denotation A Stroke S2 Part no. denotation B Stroke S1 Part no. denotation A B + Stroke S2 L B + Stroke S1 L B + Stroke S2 L L B + Stroke S1 A + Stroke (S1 + S2) A + Stroke (S1 + S2) Note) In the case of bore sizes 12 to 25 with auto switch, port directions are different.
S1 S2 S1 S2 S1 S2 S1 Master unit V BDH SD FG SD FG SD FG SD FG CANL Twisted pair wire with shield FG BDL Class 3 ground Class 3 ground Class 3 ground Class 3 ground CANH V+ Connect the shielding wire to the SD terminal.
Mount switches in locations where there is no vibration greater than 98 m/s2, or impact greater than 490 m/s2. 3. Do not use in an area where surges are generated.
Move M Speed Position Accel Decel Pushing F TriggLV Pushing Sp Moving F Area1 Area2 In pos mm/s mm mm/s2 mm/s2 % % mm/s % mm mm mm 0 Absolute 250 50.00 3000 3000 0 0 0 100 48.00 50.00 0.50 1 Absolute 250 0.00 3000 3000 0 0 0 100 0.00 2.00 0.50 [ ] Need to be set [] Need to be adjusted as required. [ ] Not used.
Maximum acceleration: 2000mm/s2 Positioning distance (mm) 1 1000 500 100 10 10 0.5 100.5 50.5 10.5 1.5 100 0.5 10.5 5.5 1.5 0.6 Speed (mm/s) 500 0.5 2.7 1.7 0.9 0.6 1000 0.5 1.9 1.4 0.9 0.6 A B C D Values will vary slightly depending on the operating conditions.
P1 LED lever meter Sensor S1 S3 Red is on: Output OFF Green is on: Output ON S4 S2 + P2 Red 1 Gap too big S1, S2: Fixed orifice S3: Variable orifice (Set via adjustment knob) S4: Detection nozzle Red 2 Green 1 BEST POSITION The bridge circuit is constructed as shown in the diagram. Position the work piece in front of the nozzle (S4).
) C8 One Touch Fitting for 8 (VQZ2000/3000) C10 One Touch Fitting for 10 (VQZ3000) M5 M5 Thread (VQZ2000/3000) 01 Rc(PT)1/8 (VQZ2000) 02 Rc(PT)1/4 (VQZ3000) CM Mixture of Port Size (VQZ1000/2000/3000) When ordering Port Mixture and/or with Port Plug, suffix it in Manifold Specs.
PT50] setting For example, for the servo motor with the rated speed of 3000 r/min, set 3000 (3 s) to increase speed from 0 r/min to 1000 r/min in 1 s. This parameter corresponds to "Profile acceleration (Class ID: 64h, Ins ID: 6083h, Attr ID: 0)".
Mount the switch in a location where there is no vibration (Display: greater than 98 m/s2, Sensor: 4.9 m/s2 or less), or no impact greater than 490 m/s2. 3. Do not use in an area where surges are generated.
Selection Example Operating conditions Workpiece mass: 0.2 [kg] W 0.6 Speed: 200 [mm/s] Lead 4 (LEPY6K) 0.5 Acceleration/Deceleration: 3000 [mm/s2] Work load [kg] 0.4 Stroke: 40 [mm] 0.3 Workpiece mounting condition: Vertical upward downward transfer Lead 8 (LEPY6J) 0.2 0.1 Step 1 Check the work loadspeed.
type) 3/8 (2000, 3000 type) 1/2 (3000 type) B C Without bracket Flat bracket L-bracket Option Option Option 14-8-14 15 Electro-pneumatic Regulator Series ITV1000/2000/3000 Combination possible Combination not possible Standard specifications Combinations ITV10 models are not applicable.
Condition 1) 30mm position Step no.0 Step no.0 (Move Method: Relative) Condition 2) 30mm position Step no.1 Step no.1 (Move Method: Relative) mm/s mm mm/s2 mm/s2 % % mm/s % mm mm mm 0 Relative 100 10.00 3000 3000 0 0 0 100 10.00 20.00 1.00 1 100 3000 3000 0 0 0 100 Relative -10.00 10.00 20.00 1.00 Position:10(Relative) c Attainment point: 50[mm] 0 10 20 30 40 50 Stroke[mm] Position:-10
The operating time for D-J51 is 2 ms or less and for D-P3DW/P4DWL is 40 ms or less. 4) 980 m/s2 for the trimmer type sensor section, 98 m/s2 for the amplifier section.
LECSS2 -T The driver power turned on while the servo motor was rotated exceeding 3000 r/min by an external force. Check if the driver power turned on while the servo motor was rotated exceeding 3000 r/min by an external force. Review the power-on timing. Overshoot/undershoot occurs. The servo gain is low or too high. The response of auto tuning is low or too high.
Tightening torque for terminal: 0.6 Nm 3-8-7 8 Series VFS1000/2000/3000/4000/5000/6000 Caution Lead Wire Connection Manifold/Plug-in Type 01F D-sub Connector Type 01C Circular Connector Series VFR2000/3000/4000/5000 Series VFR2000/3000/4000/5000 Wire connection specifications Lead wire for both solenoid A and B sides in manifold are connected to connector terminal as COM specifications.
R1 R2 SG FG 24 V 0 V S1 S2 SG 24 V 0 V S1 S2 R1 R2 SG FG 24 V 0 V S1 S2 R1 R2 SG FG 24 V 0 V Ground either the reception side or the transmission side of the shielding wire shield.
P4 is selected by the ON/OFF combination of S1 and S2.
Acceleration [mm/s2]: a Work load [kg]: m Work load center position [mm]: Xc/Yc/Zc z y 1. Horizontal 3. Wall x y x z x 2. Bottom 4. Vertical z y x y z Example 1. Operating conditions Model: LEKFS40 Size: 40 Mounting orientation: Horizontal Acceleration [mm/s2]: 3000 Work load [kg]: 20 Work load center position [mm]: Xc = 0, Yc = 50, Zc = 200 2.
Maximum manufacturable stroke (mm) Bore size (mm) Standard stroke (mm) Symbol Specifications 16 3000 100, 200, 300, 400, 500, 600, 700 800, 900, 1000, 1200, 1400, 1600 1800, 2000 -XB11 Long stroke 20, 25, 32, 40 50, 63 -XC18 NPT finish piping port 5000 -XC67 NBR rubber lining in dust seal band Strokes are manufacturable in 1 mm increments, up to the maximum stroke.
T1 = V/a1 = 200/3000 = 0.067 [s], T3 = V/a2 = 200/3000 = 0.067 [s] 40 0.5 200 (0.067 + 0.067) 200 T2 = = = 0.133 [s] L 0.5 V (T1 + T3) V T4 = 0.2 [s] Therefore, the cycle time can be obtained as follows.