Ionizer Series IZS40/41/42 To use AC adapter, specify N, and select AC adapter sold separately (on page 20).
(X10) Set upper bits of the station. 01 to 64 STATION NO.(X1) Set lower bits of the station. The CC-Link address setting at the time of the factory shipment is set in 01".
Display Description Details 1 P1, P2 EtherNet/IP communication connector Connect Ethernet cable. 2 MS, NS Communication status LED Display the status of the EtherNet/IP communication. x100 IP address setting switches Switches to set the EtherNet/IP communication IP address (0 to 255) by X1, X10 and X100. 3 x10 x1 OFF Power supply OFF 4 PWR Power supply LED (green) Green LED is ON Power supply
. output 8 PT7 RY(n 2)9 Reserved RX(n 2)A RY(n 2)A Position/speed specifying system selection to Reserved RX(n 2)F selection RX(n 3)0 RY(n 2)B Absolute value/incremental value to Reserved RY(n 2)C RX(n 3)9 to Reserved RX(n 3)A Trouble ALM 15 RY(n 2)F RX(n 3)B Remote station communication ready CRD RY(n 3)0 to Reserved RX(n 3)C RY(n 3)9 to Reserved RY(n 3)A Reset RES RX(n 3)F RY(n 3)B to Reserved
. output 8 PT7 RY(n 2)9 Reserved RX(n 2)A RY(n 2)A Position/speed specifying system selection to Reserved RX(n 2)F selection RX(n 3)0 RY(n 2)B Absolute value/incremental value to Reserved RY(n 2)C RX(n 3)9 to Reserved RX(n 3)A Trouble ALM 15 RY(n 2)F RX(n 3)B Remote station communication ready CRD RY(n 3)0 to Reserved RX(n 3)C RY(n 3)9 to Reserved RY(n 3)A Reset RES RX(n 3)F RY(n 3)B to Reserved
490 N 390 N 245 N 588 N 390 N 490 N 245 N Allowable radial load Shaft load MSU 539 N 490 N 340 N 196 N 539 N 340 N 490 N 196 N Allowable thrust load Bearing Bearing CRJ Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com Side ported or Axial ported Port location Rc 1/
RD SD LRUN PW B RATE 131 8 115 80 x1 x10 STATION NO.
1 P A Frame material Aluminium alloy Stainless steel Nil W X10 Non-standard motor Frame material Guide type None B contact specification 2 pcs.
Note) +12 to 24V 4.7k 13 14 Servo ON 1Ry 0V SV-ON 5mA 1Ry ON for servo ON 2Ry Proportional control (P actuation) 15 P-CON 2Ry ON for proportional control Reverse drive suppression Normal drive suppression N-LS 16 N-OT N-LS Open for reverse drive suppression P-LS 17 P-OT P-LS Open for normal drive suppression 3Ry 18 ALM RST Alarm reset 3Ry ON for alarm release 30VDC 50mA or less 5Ry +12 to
(1) (9) (10) (2) (3) (4) (15) (16) (7) (11) (8) (12) (5) (17) (18) (21) (19) (6) (20) (13) (14) OFF 1 PWR LED() ON 2 RUN LED() EtherNet/IP USB USB 3 USB USB LED() USB 4 ALM LED() 5 USB USB ) (+)(-) 6 C PWR (2 ) x100 7 x10 IP x1 x10 x100 IP 4Byte x1 8 MS, NS LED EtherNet/IP 9 ENC1 (16 ) 1 10 MOT1 (6 ) 11 ENC2 (16 ) 2 12 MOT2 (6 ) ) (+) 1 (+) 1 (+) 13 CI 1 2 2 (+)2 (+
When selecting "No (N)", the controller will start without uploading. The title window shown below will be displayed. When the PC is not able to communicate with the controller, the following screen is displayed. When select OK, the title window will be displayed. -12No. JXC-OMT0002-C After the initial title window is displayed, the following main window will be displayed.
(default setting) Number of occupied valve 8 outputs Number of occupied valve 16 outputs Number of occupied valve 24 outputs Number of occupied valve 32 outputs Configuration X10 2 0 9 0 0 Mark C on the unit Mark B at cable end Mark A at cable end : : Address (1) Setting of the terminal resistor X1 Content 3 4 1 2 5 0 9 1 0 8 7 : : Content 9 6 5 x10 x1 0 5 4 1 2 3 0 (default setting) Node
For actuators with a stroke more than 1000mm, set parameter PE02 (Feed function selection) to 0001 and the "Feed length multiplication (STM) (Multiplier)" value to x10. 3 59 - Configure target position (mm).
Address setting switch (x10): Sets the 10 digit of the DeviceNet node address. Address setting switch (x1): Sets the 1 digit of the DeviceNet node address. Data Rate switch: Sets DeviceNet communication speed.
3 NC 4 RXD/TXD-P 5 Shield T PROFIBUS DP BUS OUT SI IP67 PROFIBUS DP A [kbps] 9.6 19.2 45.45 93.75 187.5 500 1,500 3,000 6,000 12,000 [m] 1,200 1,000 400 200 100 -17No.EX-OMN0027CN-D (1) (2) (3) (4) (0.30.4Nm) OFF OFF 0, -18No.EX-OMN0027CN-D PROFIBUS DP (X10)PROFIBUS DP (X1)PROFIBUS DP (8)PROFIBUS DP Settings1 Address 8 X10 X1 0 0 0() 0 1 1 0 2 2 OFF 9 8 98 9 9 99 0 0 100
ECAT ID EtherCAT ID 1999(1) EtherCAT ID: 0999 (Factory default 002) Setting EtherCAT ID x100 x10 x1 0 0 0 Value that setting by EtherCAT master device 0 0 1 1 0 0 2 2 (Factory default) 0 0 6 4 64 9 9 9 999 Caution Turn OFF the power supply while setting the switch.
STATION No (X10) 161 (x10) STATION No (X1) (x1) B RATE IF CC-Link F D C 10Mbps B 5Mbps A 2.5Mbps 230.4kbps 9 625kbps 8 156kbps 7 5 4 10Mbps 3 5Mbps 2 2.5Mbps 115.2kbps 1 625kbps 0 156kbps B RATE 1(LEC-T1)IF 115.2kbps 2 15 - 4.2 (CN2SW) CC-Link (CN2SW)CC-Link (CN2SW) () PC/TB (CN2)(LEC-T1-)(LEC-W2)(LEC) (CN2SW)CC-Link (LEC) 16 - 4.3 (LEC) (LEC)(LEC-T1-) (LEC-W2)(LEC) (LEC)(LEC)(
Display Description Detail 1 LED lamp LED to indicate the condition of the gateway unit 2 ADDRESS Address switch This switch sets X1 and X10 in the address. 3 B RATE Communication speed The switch to set the communication speed of the controller IF communication line.
-HT1 EX600-DEEX600-DFEX600-AYAEX600-AMB SI EX600-SDN1 EX600-SDN1A -12No.EX-OMN0029CN-D (1) 1.51.6 Nm (2) 1 10 (SI ) (3)SI SI -13No.EX-OMN0029CN-D (4) (M3X8)(EX600-ZMV) 0.60.7 Nm SV 2 S0700 2 VQC10002 VQC20003 VQC40004 SY 2 EX600-ZMV (5)SI SI (M46) 0.70.8 Nm -14No.EX-OMN0029CN-D (1)6 (M45)(EX600-ZMB1) 2 EX600 0.70.8 Nm EX600-ZMB1 (2)()(M4) 0.70.8 Nm M42 M42 0.70.8Nm n(