5 Port Solenoid Valve 225 237.5 250 135.5 148 160.5 160.5 173 185.5 185.5 198 210.5 210.5 223 235.5 235.5 248 260.5 12 Slim Compact Plug-in Manifold Bar Base D-sub Connector F kit Slim Compact Plug-in Manifold Bar Base Slim Compact Plug-in Manifold Bar Base MIL Standard M 25 pins M Cable length: 1.5 m, 3 m, 5 m Page 15 Plug-in Manifold Stacking Base Plug Lead Manifold Bar Base Plug Lead Single Unit 14 F Series
When using the lock unit by placing it in parallel with the cylinder for driving as shown in the figure below, align the cylinder with the rod. Doing so may result in a decrease in holding force. Take additional safety measures when conducting equipment maintenance.
Built-in silencer, Direct exhaust [-S] VFS This is an exhaust port on the manifold end plate. The built-in silencer exhibits an excellent noise suppression effect. (silencing effect: 30dB) Note) A large quantity of drainage generated in the air source results in exhaust of air together with drainage. See p.1.10-196 for maintenance.
line, and the cylinder stroke can be controlled in two stages in both directions.
IP65 MADE IN JAPAN MADE IN JAPAN MADE IN JAPAN MADE IN JAPAN MADE IN JAPAN MADE IN JAPAN MADE IN JAPAN MADE IN JAPAN MADE IN JAPAN (mm) 8 7 6 5 4 3 2 1 Stations 185.5 173 160.5 148 135.5 123 110.5 98 Rail length L1 175 162.5 150 137.5 125 112.5 100 87.5 Mounting pitch L2 158 146 134 122 110 98 86 74 Manifold length L3 13.5 13.5 13 13 12.5 12.5 12 12 L4 Input block (M12) only (Pitch) P = 20
The built-in silencer has produced a clear-cut appearance.
If mounted in the wrong direction, the equipment to be connected may cause malfunction. Refer to external dimensions in pages 1-6-78 to 1-6-79, and then mount it.
IP65 MADE IN JAPAN MADE IN JAPAN MADE IN JAPAN MADE IN JAPAN MADE IN JAPAN MADE IN JAPAN MADE IN JAPAN MADE IN JAPAN MADE IN JAPAN (mm) 8 7 6 5 4 3 2 1 Stations 185.5 173 160.5 148 135.5 123 110.5 98 Rail length L1 175 162.5 150 137.5 125 112.5 100 87.5 Mounting pitch L2 158 146 134 122 110 98 86 74 Manifold length L3 13.5 13.5 13 13 12.5 12.5 12 12 L4 Input block (M12) only (Pitch) P = 20
, and the cylinder stroke can be controlled in two stages in both directions.
The built-in silencer has produced a clear-cut appearance.
The built-in silencer has produced a clear-cut appearance.
can be controlled in two stages in both directions.
20 475 Note 1) One-touch fittings in inch sizes are also available.
These products are intended for use in general factory automation equipment. Avoid using these products in machinery/equipment which affects human safety, and in cases where malfunction or failure can result in extensive damage. 2. Do not use in explosive environments, in the presence of inflammable gases, or in corrosive environments. This can cause injury or fire. 3.
Cylinder side pressure (P2) IN IN Specifications Max. operating pressure Min. operating pressure Ambient and fluid temp.
(In the case of standard cylinders, port must be positioned in the upper side.) Define the upper side to be A, and then B, C, and D in a clockwise order. 2.
These products are intended for use in general factory automation equipment. Avoid using these products in machinery/equipment which affects human safety, and in cases where malfunction or failure can result in extensive damage. 2. Do not use in explosive environments, in the presence of inflammable gases, or in corrosive environments. This can cause injury or fire. 3.
Note 2) Impact resistance No malfunction occurred when it was tested in the axial direction and at right angles to the main valve and armature in both energized and de-energized states once for each condition. (Default settings) Vibration resistance No malfunction occurred in a one-sweep test between 45 and 2000 Hz.
Note 2) Impact resistance No malfunction occurred when it was tested in the axial direction and at right angles to the main valve and armature in both energized and de-energized states once for each condition. (Default settings) Vibration resistance No malfunction occurred in a one-sweep test between 45 and 2000 Hz.