One-touch Fittings Install an air filter. Install an air filter at the upstream side of valve. Select an air filter with a filtration degree of 5 m or finer. 8. Interference in oval type release button The following models cannot be used if a box wrench or socket wrench is used. 2. Install an aftercooler, air dryer or water separator, etc.
An EXH block base assembly is used in the blocking position when ordering an EXH spacer incorporated with a manifold no. However, do not order an EXH block base assembly because it is attached to the spacer. When separately ordering an individual EXH spacer, separately order an EXH block base assembly because it is not attached to the spacer.
Fitting Connection Type Series AN-KM Specifications Can connect with One-touch fitting directly. 5 to 60C Max. operating pressure Note) Fluid Compressed air 1.0 MPa Ambient and fluid temperature Note) It indicates the inlet pressure for solenoid valve.
Fitting Connection Type Series AN-KM Specifications Can connect with One-touch fitting directly. 5 to 60C Max. operating pressure Note) Fluid Compressed air 1.0 MPa Ambient and fluid temperature Note) It indicates the inlet pressure for solenoid valve.
Furthermore, by connecting an input block, a maximum 32 sensor signal inputs are possible. SI unit for AS-i As a AS-i slave unit, this kit is capable of up to 4 or 8 points of solenoid valve ON and OFF control. Furthermore, by connecting an inmput block, a maximun 4 or 8 sensor signal inputs are possible.
Note 1) This cylinder cannot perform an intermediate stop using an air pressure circuit in vertical operation. In this case, an intermediate stop can be performed only by using an external stopper, etc. Note 2) Made-to-order products should be considered, too, depending on an operating environment, etc.
642.7 Setting range: 1 to 40 1600 PA10 INP In-position range Set an in-position range per command pulse.
642.7 Setting range: 1 to 40 PA10 INP In-position range Set an in-position range per command pulse.
An error code is returned if an instruction code outside the range set in parameter No.
An error code is returned if an instruction code outside the range set in parameter No.
6 33 M5 x 0.8 5.5 8 14 3.5 M10 x 1.25 29 1/8 9 83 13 32 10 24 to 300 22 19.5 17 20 32 12 18 12 40 6 38 M5 x 0.8 5.5 10 16 3.5 M10 x 1.25 35.5 1/8 11 85 15 40 10 to 500 24 30 27 19 26 40 16 19 13 50 8 47 M6 x 1.0 6 14 16 4 M14 x 1.5 44 1/8 11 93 15 50 14 40 to 600 35 32 27 32 50 20 21 14 58 11 58 M8 x 1.25 7 18 22 5.5 M18 x 1.5 55 1/4 15 21 109 63 14 40 to 600 35 32 27 38 60 20 21 14 58 11
In addition, by connecting an input block a maximum of 32 sensor signal inputs are possible. Input block This is an expansion block which connects to an SI unit to perform sensor input from auto switches, etc. Two or four sensor inputs can be accommodated by one input block, and the common can be matched to the sensor by an NPN/PNP switch.
6 33 M5 x 0.8 5.5 8 14 3.5 M10 x 1.25 29 1/8 9 83 13 32 10 24 to 300 22 19.5 17 20 32 12 18 12 40 6 38 M5 x 0.8 5.5 10 16 3.5 M10 x 1.25 35.5 1/8 11 85 15 40 10 24 to 500 30 27 19 26 40 16 19 13 50 8 47 M6 x 1.0 6 14 16 4 M14 x 1.5 44 1/8 11 93 15 50 14 40 to 600 35 32 27 32 50 20 21 14 58 11 58 M8 x 1.25 7 18 22 5.5 M18 x 1.5 55 1/4 15 21 109 63 14 40 to 600 35 32 27 38 60 20 21 14 58 11
Select an appropriate manifold assembly part number from the table below.
/ Complex exhaust) 40 40 100 Vacuum pressure [kPa] 30 30 80 Air consumption 60 20 20 40 High-noise reduction silencer exhaust 10 10 20 0 0 0.1 0.2 0.3 0.4 0.5 0.6 0 0 0 10 20 30 40 50 60 Supply pressure [MPa] Suction flow [L/min (ANR)] 19 Vacuum Unit ZK2mA Series The flow rate characteristics correspond to the standard supply pressure.
Conductor resistance 65/km or less, 20oC Cable 0.3mm2 x 25 cores Voltage limit AC 1000V, 1min Insulation resistance 5M/km, 20oC Note) The minimum bending inner radius of D-sub connector cable is 20mm.
VVQ5000-25A1 5 Intermediate stop Drop prevention Can hold an intermediate cylinder position for an extended time. When combined with a double check spacer with built-in double check valve, it is unaffected by air leakage between the spool valves, making it possible to hold a cylinder at an intermediate stopping position for an extended time.
Tightening of M3/M5 Threads 1) Tighten a barb fitting by hand, and give it an additional 1/6 turn with a wrench. 2) Tighten a barb elbow by hand, and give it an additional 1/3 turn with a wrench.
1 Stainless Steel Cylinder Series CJ5-S Series CG5-S 10, 16 20, 25, 32, 40, 50, 63, 80, 100 Applicable for use in an environment with water splashing such as food processing, etc. RE A B REC Uses grease for food processing machines that meets FDA (U.S.