Speed Controller for Low Speed Operation Series AS-M Standard Type (Metal Body)

With one-touch fitting For low speed control AS Needle Valve/Flow Characteristics ASP AS1001FM AS2001FM AS2051FM ASN 0.8 Inlet pressure: 0.5 MPa Inlet pressure: 0.5 MPa Inlet pressure: 0.5 MPa 10 20 50 0.15 0.3 AQ Flow rate (l/min (ANR)) Flow rate (l/min (ANR)) Flow rate (l/min (ANR)) Effective area (mm2) Effective area (mm2) Effective area (mm2) 40 0.6 ASV 0.1 0.2 30 AK 5 10 0.4 20 0.05

Speed Controller with One-touch Fitting Stainless Steel Type Elbow Type/Universal Type AS-FG Series Push-lock type

2 AQ q w ASV y t AK i VCHC o ASR ASQ !0 u !5 e Meter-out type Meter-in type Component Parts No.

Speed Controller with Indicator Stainless Steel Type Elbow Type/Universal Type AS-FSG Series

2 AQ w t y q i o e ASV AK !0 VCHC ASR ASQ u @0 Meter-out type Meter-in type Component Parts No.

Check Valve Series AK

Application Example for Check Valve with One-touch Fitting Prevention of reverse flow to vacuum source (Simple vacuum holding) Tank pressure reverse flow prevention AS ASP ASN AQ ASV AK ASS Drop prevention ASR ASF A certain amount of leakage is allowed in the specifications of this product. Please note that it is not suitable for holding over an extended period of time.

Speed Controller: Standard Type Series AS In-line Type

Retainer prevents an accidental loss of needle.

Series AP3500

It is illustrated with an arrow pointing towards the valve body or an "empty" triangle on the schematic. OUTLET (Downstream) is defined as a port connected to the region above the seat and below the diaphragm.

ASR

When the product is used for an actuator operating vertically, the actuator may lurch depending on the load. For the adjustment method, please refer to Selection and Adjustment on page 15-16-6 to 15-16-7. 4. For installation and removal, tighten the body B by applying an appropriate wrench to the two opposite sides of the hexagon. Using other parts may destroy the valve.

Vacuum

Select a valve model with an effective orifice area S.

Vacuum

Select a valve model with an effective orifice area S.

Guide Cylinder/Compact Type Series MGC

70 95 125 60 32 M8 x 1.25 1/8 104 12 38 67 4 11 8 7 M12 x 1.75 depth 21 45 82.5 115 150 75 38 M8 x 1.25 1/8 115 12 47 T U V W WH W X Y Z Bore size (mm) 20 25 32 40 30 16 112 53 50 23 30 146 182 30 20 132 63 60 25 37 167 199 25 20 132 63 60 28.5 37 167 202 20 25 162 73 70 33 44 210 227 Without Rear Plate Stroke range (mm) Long Stroke R Z Y Bore size (mm) 20 25 32 40 Bore size (mm) 20 25 32

Cooling Capacity: 100 (10 kW), Cooling Method: A (Air-cooled), Pipe Thread: N [NPT, (w/Rc-NPT conversion Fitting)]

Cooling Capacity: 10 kW, Cooling Method: Air-cooled, Pipe Thread: N [NPT, (w/Rc-NPT conversion Fitting)], Option: -

Speed Controller with Uni One-touch Fitting AS Series Push-lock type

AK VCHC 9. Do not apply excessive force or shock to the body or fittings with an impact tool. 6. Check if PTFE can be used in application. ASR ASQ PTFE powder (Polytetrafluoroethylene resin) is included in the seal material for piping taper thread of male thread type. Confirm that the use of it will not cause any adverse effect on the system.

Speed Controller with Residual Pressure Release Valve with One-touch Fitting Series AS



FE Elbow Type/Universal Type

This product cannot be used to hold a stop position for an extended period of time. Pilot check valves and actuators are not guaranteed for zero air leakage. Therefore, it is sometimes not possible to hold a stop position for an extended period of time. In the event that holding for an extended time is necessary, a mechanical means for holding should be devised. 3.

Speed Controller: Standard Type Elbow Type (Metal Body) Series AS

Retainer prevents an accidental loss of needle.

Safety Speed Control Valve (SSC Valve) Series ASS

This product cannot be used to hold a stop position for an extended period of time. Pilot check valves and actuators are not guaranteed for zero air leakage. Therefore, it is sometimes not possible to hold a stop position for an extended period of time. In the event that holding for an extended time is necessary, a mechanical means for holding should be devised. 3.

Tamper Proof Speed Controller with One-touch Fitting Elbow Type/Universal Type Series AS  1F-T

AS1001F-23D-X214 AS AS-FE KE AS-FG AS-FP AS-FM AS-D AS-T AS-D AS-T ASP ASN AQ ASV AK VCHC ASS ASR ASQ 591

Guide Cylinder Series MGG

to 50 M N Bracket (See table below.) 4-O T Q 2-P AH AG B S W K U L AA AL AB A I J AI AJ 4-AK hole V AP R Y + Stroke Z + Stroke X AG For 4-AO AN AI Cutout window AM Mounting dimensions For standard strokes (mm) Bore size (mm) Stroke range (mm) O N M L K J I B AP AO AN AM AH AG AB AA AL AK AJ AI A 20 25 32 40 50 75, 100, 125, 150, 200 M6 x 1 depth 9 45 25 80 60 55 30 108 25 M6 115 65 125 112

1

Local Area: (800) 258-9200-www.stevenengineering.com AL Width across flats 12 Element Width across flats XA Unlocking cam AP V I 4-AK hole Q PL PG J AI AJ R AB X A AG AA Y + Stroke Z + Stroke For 4-AO AN AI AM Cutout window Mounting dimensions Standard Stroke Bore size (mm) Stroke range (mm) A AA B I J K L M N GC GK GL GQ GR AB AG AH AI AJ AK AL AM AN AO AP 20 75, 100, 125, 150, 200 129 12

AS-FS Series Speed Controller with Indicator/ Elbow Type: Uni Thread Type

Connection Female Thread: Rc, NPT, NPTF Uni thread size Wrench tightening angle after hand-tightening [deg] Tightening torque [Nm] 1/8 30 to 60 3 to 5 1/4 30 to 60 8 to 12 3/8 15 to 45 14 to 16 1/2 15 to 30 20 to 22 Connection thread size Proper tightening torque [Nm] NPT, R1/8 3 to 5 NPT, R1/4 8 to 12 NPT, R3/8 15 to 20 NPT, R1/2 20 to 25 Connection Female Thread: G Chamfered area for female