LEC-OM02704CN P-D 1 P P C C G3 D (2) 1) G4 5m (1) 1.
(1) LECSS2-T P+DP+CG3G4 G3G4 P+D P+D P P+ C C G3 D (3) (1) G4 5m 5 m (12) 1.
P I S T O N R O D A I R H Y D R O TYPE P I S T O N R O D D E F L E C T I O N (REFERENCE FACTOR) P I S T O N R O D D E F L E C T I O N (REFERENCE FACTOR) For a concentrated load at the center of the housing. For a concentrated load at the center of the end plate.
I M E N S I O N S AD S E R I E S A U I T O D R A I N S S Y M B O L S H O W T O O R D E R A U T O D R A I N S E R I E S AD AD402-02 (1/4) PT AD402-03 (3/8) PT AD402-04 (1/2) PT AD600-06 (3/4) PT AD600-10 (1) PT H O W T O O R D E R A U T O D R A I N S E R I E S NAD NAD402-N02 (1/4) NPT NAD402-N03 (3/8) NPT NAD402-N04 (1/2) NPT NAD600-N06 (3/4) NPT NAD600-N10 (1) NPT FOR FURTHER TECHNICAL DETAILS
M E N S I O N S AD S E R I E S A U I T O D R A I N S S Y M B O L S H O W T O O R D E R A U T O D R A I N S E R I E S AD AD402-02 (1/4) PT AD402-03 (3/8) PT AD402-04 (1/2) PT AD600-06 (3/4) PT AD600-10 (1) PT H O W T O O R D E R A U T O D R A I N S E R I E S NAD NAD402-N02 (1/4) NPT NAD402-N03 (3/8) NPT NAD402-N04 (1/2) NPT NAD600-N06 (3/4) NPT NAD600-N10 (1) NPT FOR FURTHER TECHNICAL DETAILS
(SW1) (SW1) (SW2-3, SW2-4) (SW2-3, SW2-4) 0 33 0 49 1 34 1 50 2 35 2 51 3 36 3 52 4 37 4 53 5 38 5 54 6 39 6 55 ON ON 7 40 7 56 8 41 8 57 1 2 3 4 1 2 3 4 9 42 9 58 A 43 A 59 B 44 B 60 C 45 C 61 D 46 D 62 E 47 E 63 F 48 F 64 -14- 5. Parameter list (Driver side) Please configure the appropriate parameters to enable correct driver operation. Refer to [5.
A 3.0 D Specification Element Model A B SCFM Nm3/h C D In/Out Side Bottom Lbs Dimensions (in) Connections (NPT female) Flow Rate Weight Model Number 5.5 1/4 1/8 male 1 1.25 6 14 4.5 AFW150-N10DG-[a] 255 EL-AFW150-[a] 150 12 1/2 1/4 1-1/2 1.5 6.5 19 5.75 AFW225-N14DG-[a] 382 EL-AFW150-[a] 225 12 1/2 1/4 1-1/2 1.5 6.5 19 5.75 AFW300-N14DG-[a] 510 EL-AFW150-[a] 300 B 12 1/2 1/4 2 1.5 6.5 19
Table 3-6 RTU mode message frame a) Start b) Device Address c) Function d) Data e) Checksum (CRC) f) End T1-T2-T3-T4 XX XX XX XX XX XX T1-T2-T3-T4 a) Start In Modbus RTU mode, message frames are separated by a silent interval (non-communication time).
Series HRS100/150 CAT.NAS40-62B R410A as refrigerant Thermo-chiller Standard Type Series HRS100/150 Circulating Fluid Temperature Controller Triple controller Fan Air-cooled condenser fan control Cooling valve Heating valve Circuit diagram Ventilation Cooling valve control Fan Facility water outlet Temperature sensor (Heat exchanger inlet) Water-cooled condenser Dryer Air-cooled condenser D
-phase 200 VAC 3-phase 400 VAC [mm] [mm]
Hook spanner flat Bowl O-ring Bowl assembly Detent: 4 places Lock button Setting mark 412 AL50/AL60 Exploded View 2 Lubrication plug assembly Actuators Modular F.R.L.
Hook spanner flat Bowl O-ring Bowl assembly Detent: 4 places Lock button Setting mark 412 AL50/AL60 Exploded View 2 Lubrication plug assembly Actuators Modular F.R.L.
Writing Readout Run/Stop Circulating fluid temperature setting (SV) Circulating fluid present temperature Circulating fluid discharge pressure Status information Alarm occurrence information Item Specifications Connector type D-sub 9-pin, Female connector Protocol Modicon Modbus compliant/Simple communication protocol Standards EIA standard RS-485 EIA standard RS-232C To the thermo-chiller
Grounding class: D-class grounding (with a ground resistance of 100 or less) 3.3.3 Preparation and wiring of power supply cable The electrical facilities should be installed and wired in accordance with local laws and regulations of each country by a person who has knowledge and experience. Check the power supply.