Bore Size: 6mm, Port Thread: M Thread: 6 to 15 Bore; Rc: 20 to 63 Bore, Symmetric Type: Standard, Stroke: 10mm, Adjuster: w/o Adjuster, Auto Switch: M9N--Solid State, Gen. Purpose, 3 Wire NPN, Horizontal, Lead Wire or Prewired Connector: -, Number: -
Bore Size: 6mm, Port Thread: M Thread: 6 to 15 Bore; Rc: 20 to 63 Bore, Symmetric Type: Standard, Stroke: 20mm, Adjuster: Retracting Stroke End Adjuster/Rubber Stopper, Auto Switch: M9N--Solid State, Gen. Purpose, 3 Wire NPN, Horizontal, Lead Wire or Prewired Connector: -, Number: -
Thermo-dryer Given an ambient temperature at 86F (30C) and a relative humidity 60%. 1. Trace the arrow mark from the point A at an ambient temperature 86F (30C) to obtain the intersection B on the curved line for the relative humidity 60%. 2. Trace the arrow mark from the intersection B to obtain the intersection D on the pressure characteristic line for 102psi (0.7 MPa). 3.
Given an ambient temperature of 30C and a relative humidity of 60%. Trace the arrow mark, from point A of ambient temperature 30C to obtain the intersection B on the curved line for the relative humidity of 60%. Trace the arrow mark, from the intersection B to obtain the intersection D on the curved line for the 0.7 MPa pressure characterisitics.
Bore Size: 6mm, Symmetric Type: Standard, Stroke: 30mm, Adjuster: C (Both Side Adjusters/Metal Stoppers)
Bore Size: 6mm, Symmetric Type: Standard, Stroke: 30mm, Adjuster: Both Side Adjusters/Metal Stoppers, Function: -, Auto Switch: -, Lead Wire or Prewired Connector: -, Number: -
This system Your system Communication data TEMP PV 30C TEMP PV TEMP PV 30C TEMP SP 30C External communication 30C Discharge temp: OFFSET 1C 31C dissipation: Heat 1C Circulating fluid temp. in your system: 30C Figure 8-7 When MODE3 is selected HRW Series 8.4 Offset Function 8-11 HRX-OM-K003 Chapter 8 Appendix 8.5 BAND/READY function Sets BAND to TEMP SP value, and notifies TEMP PV value reaches
) : Not available Single rod Double rod Cushion Page Air Rubber Air Rubber 392 402 Symbol Specifications Applicable bore size 32 to 100 125 32 to 100 125 32 to 100 125 32 to 100 125 Standard Standard V V V V V V V V Long st Long stroke V V V V V V V V 32 to 125 D Built-in magnet V V V V V V V V MBl-lJ K With rod boot V V V V V V V V 25A Copper (Cu) and Zinc (Zn)-free Note 1) 32 to 100 V
1 series 10C 20C 30C Standard model (Normal operation) Set dew point Accumulated running hours display Helps maintenance control of the dryer. Gives notice of the maintenance timing etc. 1. Energy saving operation (ECO LED is ON green): Dew point can be set manually between 10 to 30C. 2. Normal operation (ECO LED is OFF): Dew point is fixed to 10C. Description No.
CS2*-OM0237Q PRODUCT NAME AIR CYLINDER MODEL / Series / Product Number 25A-CS2*125160-** 3 2/5 Contents 1. Safety Instructions P.2 2.
Auto switch model Lead wire length (m) Load voltage Special function Type Electrical entry Indicator light Wiring (output) CX2 Pre-wired connector Applicable load 0.5 (Nil) 1 (M) 3 (L) 5 (Z) AC DC Perpendicular In-line CXW M9N M9P M9B M9NW M9PW M9BW M9NA M9PA M9BA M9NV M9PV M9BV M9NWV M9PWV M9BWV M9NAV M9PAV M9BAV 3-wire (NPN) 5 V, 12 V IC circuit 3-wire (PNP) Solid state switch Reed switch
Cool from 30C (303 K) to 20C (293 K). : Clear water Density : 1 x 103 kg/m3 Specific heat C: 4.2 x 103 J/(kgK) Water bath Refer to the information shown below for the typical physical property values by circulating fluid.
Given an ambient temperature at 86F (30C) and a relative humidity 60%. 1. Trace the arrow mark from the point A at an ambient temperature 86F (30C) to obtain the intersection B on the curved line for the relative humidity 60%. 2. Trace the arrow mark from the intersection B to obtain the intersection D on the pressure characteristic line for 102 psi (0.7 MPa). 3.
The intersection E is the dew point under pressure 0.7 MPa with the ambient temperature of 30C and the relative humidity of 60%. Value for E is at 62C. 5. Trace the intersection E upward, and C leftward to obtain the intersection D. 6. The intersection C is the amount of water included in the compressed air 1 m3 at 0.7 MPa with the pressure dew point of 62C.
Once the discharge temperature of the circulating fluid becomes 31C, 1C-thermal dissipation is occurs to allow the circulating fluid in your system to be 30C. TEMP SP value is obtained for your system. TEMP PV and communication data also express 30C (circulating fluid discharge temp. value OFFSET value) that agrees with the temperature of the circulating fluid in your system.
Once the discharge temperature of the circulating fluid becomes 31C, 1C-thermal dissipation is assured to allow the circulating fluid in your system to be 30C. TEMP SP value is obtained for your system. TEMP PV and communication data also express 30C (circulating fluid discharge temp. value OFFSET value) that agrees with the temperature of the circulating fluid in your system.
(Note 4) Perfect dry air (dew point equals to -30C) No grease on main valve.
Conditions/Inlet air pressure 0.7 MPa Inlet air temperature 30C Precautions Pink Be sure to read before handling. Refer to pages 14-21-3 to 14-21-4 for Safety Instructions and Common Precautions on the products mentioned in this catalog, and refer to pages 14-14-6 to 14-148 for Precautions on every series.
1.00 4.18 x 103 1.00 1 x 103 30C 1.01 3.91 x 103 1.01 0.94 x 103 35C 0.99 4.18 x 103 0.99 1 x 103 35C 1.01 3.91 x 103 1.01 0.94 x 103 40C 0.99 4.18 x 103 0.99 1 x 103 40C 1.01 3.92 x 103 1.01 0.94 x 103 Note) The above shown are reference values.
AMG Color of indicator Dew point temperature (Atmospheric pressure) 30C or less 18C 10C Dark blue Light blue Light pink Conditions/Inlet air pressure 0.7 MPa Inlet air temperature 30C Please use the adsorbent set (refer to page 134 for Accessory/ Replacement Parts) when replacing the adsorbent. AFF Piping Caution AM AMD 1.