VNC Installing a silencer to the exhaust port and the bleed port is recommended for noise reduction and for dust entry prevention.
Lubrication cannot take place under a pressurized condition. 0.02 0 0 2000 4000 6000 8000 Caution Flow rate (/min (ANR)) 1. Check the dripping amount once a day.
Note 3) Use at a speed within the absorption capacity range. Refer to page 1211.
retraction stroke end adjuster with a buffer mechanism, use a buffer and centralized adjuster provided with a retraction stroke end adjuster on the rear end of the body.
Fittings & Tubing Air Cylinders Rotary Actuators Side tapped mounting [1/N1] Through-holes in open/close direction [2/N2] 4 x MM through Thread for mounting attachment C C B A 4 x H through Hole for mounting attachment S S O O B A (mm) (mm) MM M2.5 x 0.45 M3 x 0.5 M4 x 0.7 M5 x 0.8 C 2 2.5 4 5 H 2.9 3.4 4.5 5.5 B 5.7 7 9 12 B 5.7 7 9 12 Model A 3 4 5 6 Model A 3 4 5 6 11221122112211221 N1
B Locking ' Special Order option t Consult factory for availability NVF 1100-ODO{IT (drx ) Lamp and Sorga Protec-tion Z rv/Lamp/Surge Protection S dsurqe Protection Onlv L.mp and S dsurge Only BRACKET (Sutfix "F') .[ otMEr{stoNs A B c D E F 1.35 (34.41 1.34 (34.11 0.61 115.4) 0.83 Q 1 t 1.76 1.77 (44.9) Millamte.s in Parenthe$s rxfENsroNs A B c D E F G H J K It N o P o R 64.7) 0.83 (21) l.t
0.2mm Max.DC30V,50mA A /B DC500V,50M (12V ) 33.3Hz 6.8G XY 2 Z 4 JIS D1601 30G XYZ 3 IP65IEC 5m10m15m20m 1CEU2 CEU1CEU5 14 4-3 () 200 1 L=1mm 6P6200.0( CEU2 ) L PRG STEP P6 200.0 2 1 200 300mm/sec 50% 35% 15 5-1 CE2 A A B B C C O M (OV) D C O M (OV) E +1224V F 0V G H 5-2 CEU1 CEU2 CEU5 CEU*3 +12V +12V COM +12V +12V COM +12V DC12V60mA .. 16 5-3
11 B 6.5 9 12 15 A 9.5 13.5 11.5 14 B 6 8.5 11.5 14.5 A 9 13 11 13.5 32 40 50 63 2.7-6
Power saving circuit is only available for the Z type. W: With connector cable Note) Note) When placing an order for body ported solenoid valves as a single unit, the mounting screws for the manifold and gasket are not attached. Order them separately, if necessary. (For details, refer to page 100.) CEcompliant DC AC 43
AW*-OMF0053-A PRODUCT NAME MICRO MIST SEPARATOR REGULATOR MODEL/ Series AWD20-(F,N)01(F,N)02(B,C,E,G,H)(-1,2,6,C,J,N,R,Z) AWD30-(F,N)02(F,N)03(B,C,D,E,G,H)(-1,2,6,8,J,N,R,W,Z) AWD40-(F,N)02(F,N)04(B,C,D,E,G,H)(1,2,6,8,J,N,R,W,Z) Contents PAGE 1. SAFETY INSTRUCTIONS 15 2. APPLICATION 6 3. SPECIFICATIONS 6 4. HOW TO ORDER 6 5. MAXIMUM APPLICABLE FLOW RATE 7 6.
(Note) Indicator oanel Denatured PPO Swagelok* IS a registered trademark 0 1 Crawford Fitting Co. VCRlI lS a registered trademark. of Cajon Co.
Vacuum switch unit Filter unit Release flow rate adjusting needle Manual operation Vacuum switch Electrical entry Ejector exhaust Electrical entry PV/V port size Pilot valve Components Vacuum switch unit Valve unit N.C. type Ejector unit ZX1 1 10 5 L Z E C K1 L Vacuum switch unit Ejector unit 1 10 L Z E C K3 5 ZX1 Valve unit N.O. type Vacuum switch unit ZX1 1 10 E C Ejector unit CE compliant
B Locking ' Special Order option t Consult factory for availability NVF 1100-ODO{IT (drx ) Lamp and Sorga Protec-tion Z rv/Lamp/Surge Protection S dsurqe Protection Onlv L.mp and S dsurge Only BRACKET (Sutfix "F') .[ otMEr{stoNs A B c D E F 1.35 (34.41 1.34 (34.11 0.61 115.4) 0.83 Q 1 t 1.76 1.77 (44.9) Millamte.s in Parenthe$s rxfENsroNs A B c D E F G H J K It N o P o R 64.7) 0.83 (21) l.t
SY series valves have polarity when the electrical entry is a grommet or L/M plug connector with a surge voltage suppressor (option “S” or “Z”). The red lead wire is positive (+) and the black lead wire is negative (-). SY series plug-in type valves also have polarity when the type with a surge voltage suppressor (option “S,” “Z,” “NS,” or “NZ”) is selected.
Make a model selection, considering a load according to the graph on pages 439 to 445.
Refer to page 17-3-65 for ordering a coil only.
B A Through-hole (Standard) Both ends tapped style RHC Note 1) Since 12 uses a common tube for both A and B, only B is used for part no. denotation.
Bore size [mm] 10 16 20 25 Fluid Air Action Double acting A large amount of gripping force is provided through the use of a double piston mechanism, while maintaining a compact design.