Speed Controller with Indicator Stainless Steel Type Elbow Type/Universal Type AS-FSG Series As a guide, tighten it by hand, then turn it two or three turns with a wrench. Check the dimensions of each product for the hexagon width across flats.
HOUR METER 19 Records the accumulated time an Output or Input signal has been ON SCHMITT TRIGGER 19 Turn an Input On at the High Value and Off at the Low Value (or vice versa) ZONE COMPARE 20 Compare a value to a range of values (Analog, Direct Set, or FB values) DISPLAY * Display Messages or Data on the LCD display OFFSET GAIN 22 Manipulate Analog Values; y = A/B*x + C; Set High and Low
A counter clockwise until it stops (approx. 45). 4) Install a new element on cover A and insert it into the case.
side B side LES LEPY LEPS q 0.08 C side LER w LEFG32 (L = 30 mm) Displacement [mm] 0.06 LEFG25 (L = 25 mm) D side LEH LEFG16 (L = 20 mm) 0.04 LEY -X5 Model Traveling parallelism [mm] (Every 300 mm) LEFG40 (L = 37 mm) q C side traveling parallelism to A side w D side traveling parallelism to B side 11LEFS 0.02 LEFG16 0.05 0.03 LEFG25 0.05 0.03 11LEJS LEFG32 0.05 0.03 0 0 100 200 300 400 500
How to order JMHZ2 16 D M9B S X7500 A C KR Number of fingers *Note 2) For KAWADA ROBOTICS CORPORATION 2 2 Number of auto switches Protection cover Bre bize[mm] Nil. Without protection cover Nil. 2 16 16mm C With proctection cover S 1 Action N n D Double acting Test attachment *Note1) Nil. Without attachment Auto switch A With attachment Auto switch No.
To release residual pressure, select a model with a backflow function. Using a model without a backflow function makes for inconsistent residual pressure release (i.e., residual pressure may or may not be released) depending upon the operating conditions. 3.
To release residual pressure, select a model with a backflow function. Using a model without a backflow function makes for inconsistent residual pressure release (i.e., residual pressure may or may not be released) depending upon the operating conditions. 3.
(A,MR~~N '(lmjQ' . 180 600 1100 1190 [Ereo flaw) Effettive ~IOnal 11.6 17 2.9 5.2 18.4 5.4 9.3 'ttrea mm 2 . N01e} The iMicaled 110w rate values are al a pressure 01 O.5MPa and a temperature 01 20 Q C. 1 Speed Controller 5 .
Flow Characteristics/Weight C [dm 3/(sbar)] b Cv C [dm 3/(sbar)] b Cv 1 2 (P A) 2 3 (A R) Valve model Flow characteristics Weight (g) Operating pressure range (MPa) Port size Grommet DIN terminal 0.10 0.13 0.13 0.10 0.13 0.13 0.13 0.13 0.13 0.13 0.41 0.32 0.32 0.41 0.32 0.59 0.32 0.32 0.59 0.32 2 3 2 3 2 3 VKF33 VKF33 Y VKF33 E VKF33 V VKF33 W VKF334 VKF334Y VKF334E VKF334V VKF334W 0.67
ANm0m0-KMmm 5.2-4 40dB(A): High Noise Reduction Silencer Series ANA1 A high noice reduction style silencer keeps the noise level inside a plant below 85dB(A).
Dimensions L plug connector M8 connector C Contact us for the dimension for Grommet type, M plug connector type, and AC type. Nozzle *L: Nozzle length Note) The nozzle and flareless fitting are included in the same package unassembled. Refer to "How to mount to mount a nozzle on the next page for the assembly instructions. 3 5. How to mount a Nozzle 1.
Set the operating pressure using the graphs as a guide.
When a needle valve is turned clockwise, it is closed and actuator speed decreases. When a needle valve is turned counterclockwise, it is open and actuator speed increases. ASV 5. Sonic conductance (C) and critical pressure ratio (b) values for products are representative values.
A MPa ON kPa OUT1 OFF OUT2 CH 1 2 3 4 PRESSURE Min. B Released SET Work 1 Work 2 Work n Atmosphere Max. A: Maximum pressure value when work piece is adsorbed. A B 4 ON = A A B 4 SET OFF = B + Min. B: Minimum pressure value when work piece is not adsorbed. OUT1 auto preset For adsorption verification: In this mode, repeat the adsorption and release of the work piece for a few times.
94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com (mm) Elbow Straight A One-touch fitting size 4, 5/32" 6 1/4" C 18 20 20.5 B 10.4 12.8 13.2 B A 20 22.4 22.8 C B 14.4 11.2 B Straight Elbow With One-touch fitting With bracket 42.5 10 15 4.2 3 22 30 20 25 20 SMC 45 30 1.8 35 35 16-2-10 11 Series ZSE30/ISE30 High Precision, 2-color Display Digital
As a guide, tighten it by hand, then turn it two or three turns with a wrench. Check the dimensions of each product for the hexagon width across flats.
Panel mounting Insert panel mount adapter B (supplied as an accessory) into section A of panel mount adapter. Push panel mount adapter B from behind until the display is fixed onto the panel. The pin of bracket engages the notched part of panel adapter section C to fix the display. The switch can be mounted on a panel with a thickness of 1 to 3.2 mm.
Caution Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. Warning 1.