PFxx-OMO0004CN ) CE 050 -8No.PF-OMO0004CN-E * 10 /23% 3 * OUT * 23 -9No.PF-OMO0004CN-E PFMB 7 A*8 201 2~200L/min 8 2 (11) S () C8 8(5/16") *6 02*1 Rc1/4 M SI*7 N02*1 NPT1/4 6 F02*1 G1/4*2 SI 1 2ISO1179-1 7:L/min :L 1 (11) L*3 3 OUT1 OU2 A NPN NPN B PNP PNP C NPN (1~5V) D NPN (4~20mA) E*4 PNP (1~5V) F*4 PNP (4~20mA) G*4 NPN *5 H*4 PNP *5 4 5 -10No.PF-OMO0004CN-E 1 W N (2 m) (2 m) + () 2 R
[H_1] Hysteresis of OUT1 25 50 100 [F 3] [ r ES] Response time [ 1.0] 1 second Mounting screws Caution Knurled part [P_2] Set value of OUT2 [F10] [ SUb] Sub display [ oUt] Set value 500 250 1000 Reset the accumulated flow. (Press the and buttons simultaneously for 1 second or longer).
R Rated flow range The flow range within which the product will meet all published specifications.
R Rated flow range The flow range within which the product will meet all published specifications. Rated pressure range The pressure range that satisfies the specifications. Repeatability Reproducibility of the display or analogue output value, when the measured quantity is repeatedly increased and decreased.
R Repeatability Reproducibility of the display or analogue output value, when the measured quantity is repeatedly increased and decreased. Response time The delay time until the set value reaches 63% in relation to the step input. S Set point range The range of ON/OFF threshold values that can be set for those products with a switch output.
Leakage voltage When a resistor and a switching element are used in parallel or C-R device (surge voltage suppressor) is used for the protection of the switching device, note that leakage voltage will increase because earth leakage current passes through the resistor and C-R device. The suppressor residual leakage voltage should be 0.2 VDC or less.
Configuration One thermo-chiller for one master. 2 2 R D R D 3 3 S D S D 5 5 S G S G Master This product Do not connect any wire to other PIN numbers. Fig. 3-15 Connection of RS-232C HRS Series 3.3Installation 3-27 HRX-OM-S004 Chapter 3 Transport and Setting Up 3.4 Piping Piping port size Connect piping firmly.
Apr R AR BR CR DR ER FR . May S AS BS CS DS ES FS . Caution If instructions are not followed there is a possibility of injury or equipment damage. Jun T AT BT CT DT ET FT . When dispose the product, contact an industrial waste disposal company for disposal of the product. To minimize the risk, drain the fluid from the product when it is scrapped.
Response delay (Small LED) T h e r m o s t a t is disabled. Filter time setting Sets the response delay time. Ambient temperature is too high. (out of 10-35oC) Correct the ambient temperature within the specification range. SV C 0 to 250 ms 0ms 4 Filter clogged Clean the filter. Set with [] or [] key The fan breaks Check the fan operation. If the fan breaks, need to be replaced.
Apr R QR RR SR . ZR AR BR . Jul U QU RU SU . ZU AU BU . Month Q R S . Z A B . Oct X QX RX SX . ZX AX BX . T With stand for vertical installation 8 1 15 9 D-sub 15 pin (Socket type) Fixed screw: M2.6 Description No.
Configuration One thermo-chiller for one master. 2 2 R D R D 3 3 S D S D 5 5 S G S G Master This product Fig. 3-13 Connection of RS-232C HRS Series 3.3 Installation 3-25 HRX-OM-W032 Chapter 3 Transport and Setting Up 3.4 Piping Piping port size Connect piping firmly. Incorrect piping might cause leakage of supplied or drained fluid and wet surrounding area and facility.
connector Connector Z None Standard Stroke Range of manufacturable stroke Standard stroke (mm) Tube Bore(mm) Without Gaiter With Gaiter Without Gaiter With Gaiter 40 25850 25700 1200 950 50 25800 25650 1150 900 63 25800 25650 1150 900 80 25750 25600 1100 900 4-2 Controller 100 25750 25600 1100 850 CEU2 Output Method None NPN Open Collector P PNP Open Collector 16 4-3 Extension Cable CE1-R
Example on Cable Connection Extension Cable (CE1-R) Note 1. Clamp and fix the connector and sensor connection to reduce tension acting on them. 2. Separate cable with power line to prevent from the occurring of noise. 3. When cable is necessary to have U bend, set the bending radius to be above 30mm.
This matches the controller. (1) LESYH16RGA-50C -5- Construction R Type as shown Case of Straight Conponent parts No. Description Material Remarks No.
Particularly when using a C-R element (surge voltage suppressor) to protect the switching element, take note that leakage current will flow through the C-R element, thus increasing leakage voltage AC coil is 8% or less of the rated voltage. DC coil is 3% or less of the rated voltage. 2.
Solenoid valve drive for AC with a solid state output (SSR, TRIAC output, etc.) 1) Current leakage When using a snubber circuit (C-R element) for surge protection of the output, a very small amount of electrical current will continue to flow even during the OFF state. This results in the valve not returning.
Leakage voltage Take note that the leakage voltage will increase when a resistor is used in parallel with switching element or a C-R circuit (surge voltage suppressor) is used for protecting a switching device because of the passing leakage voltage through the C-R circuit. The suppressor residual leakage voltage should be as 3% or less of the rated voltage. 3.
Year Month T : 2015 o: January U : 2016 P: February V : 2017 Q: March W : 2018 R: April X : 2019 Z: December -7- 5. Precautions for handling Fluid Warning (1) The operating fluids must be compressed air.
Caution Leakage voltage When a resistor and a switching element are used in parallel or C-R device (surge voltage suppressor) is used for the protection of the switching device, note that leakage voltage will increase because earth leakage current passes through the resistor and C-R device. Keep the leakage voltage as shown below.
Swollen " spool ass'y " ring Excessive amount of lubricant Leakage Air leaks through exhaust 3(R) port of main valve Worn " spool ass'y" ring Intrusion of foreign matter Spool valve has not completely shifted Poor seal on actuator (cylinders, etc.) side Insufficient bolt tightening Air leaks through gasket -SYJ500*-OMJ0001-A Remedy No.