SMC Corporation of America
Elite Part Number Search
Search Results "AL20-F02-C-A"

/min 1000 L/min PF3A702H 20 L/min 2000 L/min 1: Analogue output accuracy is within 3%F.S. 2: A and C change based on the setting of zero cut-off function. 3: Set the current to the analogue output from the connected equipment to 20 A or less when selecting 0 to 10 V.

Since a large quantity of liquid will be pumped out, use a suitable throttle in the discharge port if problems occur. Note 3) With a low number of operating cycles, even a valve with a small Cv factor can be operated.

Direct Operated Solenoid Valve Metal Seal Series VS4 10 Model Flow characteristics Max. (1) operating cycle (cpm) (3) VK Response (2) time (ms) Weight (kg) Model Port size Rc (Nominal size) Number of positions JIS Symbol P A/B A/B EA/EB VZ C [dm 3/(sbar)] C [dm 3/(sbar)] b b Cv Cv AC DC AC DC AC DC VS4110-01 (6A) 3.2 3.2 0.42 0.37 0.86 0.80 1 8 2 (Single) 1,200 180 13 or less 45 or less

For actuators with external stopper, the rotation end can be set within the ranges shown in the drawing by adjusting the stopper bolt. c l o r c e k t n w u i s o e c B port A port e c s l o i w c k Basic type For 90 and 100 For 180 and 190 Single flat Single flat +8 0 +10 0 90 0 or 10 B port A port B port A port t f fla or t f le fla ng si le ng of e si ng of ra n ge io +8 0 at an ot R

In a location exposed to corrosive or flammable gases or solvent. The option C is coated with a special epoxy paint on the surface of the copper tube to improve anti-corrosion resistance to corrosive gases, but cannot prevent rust completely.

G Across flat A A 1/16 Radial float H 1 Spherical motion E D B C E Dimensions H 1 1/2 2 1/4 2 1/4 Part No. NCA1-AC325 NCA1-AC800 NCA1-AC1000 A 3/4-16 1-14 1 1/4-12 B 1 3/4 2 1/2 2 1/2 C 2 5/16 2 15/16 2 15/16 D 5/16 1/2 1/2 E 1 1/8 1 5/8 1 5/8 F 31/32 1 3/8 1 3/8 G 7/8 1 1/4 1 1/4 Pivot Pins CP DD CL CD CL CD Dimensions Dimensions CL 2 5/8 3 1/8 4 1/8 CP 2.72 3.22 4.25 Part No.

In an environment where the product will come into direct contact with rain, wind and snow or with a lot of moisture (relative humidity 85% or more). (Note) In a location with a large quantity of dust. In a location containing flammable or explosive gases. In a location exposed to corrosive or flammable gases or solvent.

Since a large quantity of liquid will be pumped out, use a suitable throttle in the discharge port if problems occur. Note 3) With a low number of operating cycles, even a valve with a small Cv factor can be operated.

Since a large quantity of liquid will be pumped out, use a suitable throttle in the discharge port if problems occur. Note 3) With a low number of operating cycles, even a valve with a small Cv factor can be operated.

C a u t i o n Use a specific mounting bracket (Table 2) and mount the product so that the band of the bracket will be perpendicular to the stroke of the product. Tighten mounting screws to the appropriate torque. The auto switch can only be used for cylinders with a built-in magnet for auto switch (e.g. CDM2).

C a u t i o n Use a specific mounting bracket (Table 2) and mount the product so that the band of the bracket will be perpendicular to the stroke of the product. Tighten mounting screws to the appropriate torque. The auto switch can only be used for cylinders with a built-in magnet for auto switch (e.g. CDM2).

C A phenomenon that may occur in a fluid moving at a high speed. In the areas within the fluid where the pressure is low, vapor bubbles form and then rapidly collapse. If cavitation is present for a prolonged period, exposed surfaces will be damaged; this is referred to as cavitation damage or, erosion.

Especially avoid the application of pressure through a water hammer, which is above the specification. a) Use a device such as a water hammer relief valve to slow the valves closing speed. b) Absorb impact pressure by using an accumulator or elastic piping material such as a rubber hose. c) Keep the piping length as short as possible. 8.

Displacement Use in a strong light source. Check that the Card Motor is not exposed to a strong light source such as direct sunlight. Install a light shielding plate as a cover.

(mm) At the minimum stroke of 25 mm adjustment bolt Basic stroke At maximum stroke adjustment At the minimum stroke of standard adjustment bolt Bore size (mm) Adjustment bolt fixing bolts Tightening torque Adjustment width across flats Bore size (mm) 10 15 25 10 15 25 A 2 A 26 A = 0.8 A = 0.6 A 0 M3 1.0 to 1.3 Nm 4 A 2 A 26 M5 4.6 to 6.2 Nm 5 Adjuster holder Adjuster holder A Adjustment

(mm) At the minimum stroke of 25 mm adjustment bolt Basic stroke At maximum stroke adjustment At the minimum stroke of standard adjustment bolt Bore size (mm) Adjustment bolt fixing bolts Tightening torque Adjustment width across flats Bore size (mm) 10 15 25 10 15 25 A 2 A 26 A = 0.8 A = 0.6 A 0 4 M3 1.0 to 1.3 Nm A 2 A 26 5 M5 4.6 to 6.2 Nm Adjuster holder Adjuster holder A Adjustment

Avoid especially the application of pressure above specifications through a water hammer. a) Use a device such as a water hammer relief valve to slow the valve's closing speed. b) Absorb impact pressure by using an accumulator or elastic piping material such as a rubber hose. c) Keep the piping length as short as possible. 8.

Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Caution: Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Warning: Danger : Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.

surface)) Low-noise fan: 48 dB(A) (Measured at a distance of 300 mm from the workpiece), Rapid static neutralizing fan: 57 dB(A) Offset voltage (Ion balance): 13 V With alarms for Incorrect high voltage, Maintenance warning With flow rate adjustment function (IZF10R) Based on ANSI/ESD-STM3.1-2006 standards 6 C O N T E N T S IZF21/31 IZF10/IZF10R Technical Data IZF21/31 Series IZF10/IZF10R