3-Screen Display High-Precision Digital Pressure Switch ∗1 ® New New The ∗1 Excluding the Z/ISE20B-L compatible type has been added to the 20B series. 5 1.5 M5 female thread Lead wire with connector If there is a possibility that the atmospheric vent port of the switch will be exposed to water or dust, insert a tube into the atmospheric vent port and route the other end of the tube to a safe place away from water or dust.
When a cylinder is used in a clamping mechanism, there is a danger of work pieces dropping if there is a decrease in clamping force due to a drop in circuit pressure caused by a power outage, etc. Therefore, safety equipment should be installed to prevent damage to machinery and/or human injury. 6. Consider a possible loss of power source.
Caution: Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning: Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger : Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. Warning 1.
Do not use a screwdriver with a large grip or with a tip that does not fit into the trimmer groove because this could strip the groove.
Mounting Caution Caution For M5, 10-32UNF For G Thread (Face seal type) Tightening method Chamfered area for female thread (Recommended value) 1. Conforming to ISO 16030-2001, the chamfered dimensions shown in the First, tighten it by hand, then give it an additional 1/6 turn to 1/4 turn with a wrench. A reference value for the tightening torque is 1 to 1.5 Nm.
Series 25 19 dB (A) Page 5-10-4 VEX AN101-01 AN110-01 AN120-M5 AN120-M3 BC sintered body type Ideal for the exhaust of a compact valve or pilot air. 16 dB (A) 21 dB (A) 18 dB (A) 13 dB (A) 100 m AN Page 5-10-5 Silencers Exhaust Cleaner 70 m AMC One-touch fitting connection type Can connect with One-touch fitting directly. 25 dB (A) 30 dB (A) It differs depending upon the model.
OUT OUT Proper Auto Switch Mounting Positions (Stroke End) Proper Auto Switch Mounting Positions(Series CE1) Auto switch (mm) Bore size (mm) Auto switch model Symbol 20 32 40 50 63 12 A B A B A B A B A B A B A B A B A B 40.5 47 55 79 82 85.5 D-A7, A8 4 13 17 39 44 41.5 41 47.5 55.5 79.5 82.5 86 D-A7lH, A80H, A73C, A80C, D-F7l, J79, F7lV, J79C 4.5 13.5 17.5 39.5 44.5 42 A B 38 44.5 52.5 76.5
Spring 134313 o AWM Dimensions AWD K A Model ARJ1020F-M5-04 ARJ1020F-M5-06 21 22 B 10.4 12.8 C 4 6 D E F 10.6 (Width across flats: 10) G H J Caution 17.2 M5 X 0.8 6 3.5 15.5 50 ITV qRelease the lock to adjust the pressure. After the adjustment, engage the lock. Failure to observe this procedure could damage the handle or cause the secondary pressure to fluctuate.
Valve model Port size L J H G F E D C A B VCW20-12-01A VCB2 1/8, 1/4 13 6 4.5 5 12.8 12.8 30 25 40 34 VCW30-12-02A 1/4, 3/8 19 7 5.5 6 19 19 40 30 52 42 VCB3 VCW30-12-04A 1/2 23 7 5.5 6 23 23 44 36 56 48 VCW40-12-02A 1/4, 3/8 19 7 5.5 6 23 23 40 30 42 52 VCW30-12-04A VCB4 1/2 23 7 5.5 6 23 23 44 36 56 48 VCW40-12-06A 3/4 26 7 5.5 6 28.2 28.2 53 44 56 65 Two mounting screws (for mounting
If adjustment is performed at a pressure other than atmospheric pressure, the correct value will not be displayed. 4. Tighten One-touch fittings in accordance with the following. One-touch fittings should first be tightened by hand, and then further tightened approximately 1/6 of a turn using a tightening tool.
06 6 (mm size) KJH06-M5 Specifications Model PPA100 for high press.
AS1200-M3 AS1400-M3 AS120-M5 AS220-01AS220-02 AS320-03 AS420-04 10-32UNF Port size M3 x 0.5 2.5, 4, 6 1.05 MPa 0.7 MPa 0.1 MPa M5 x 0.8 1/8 1/4 20, 25, 32, 40 3/8 1/2 6, 10, 15, 20, 25 80, 100 32, 40, 50, 63 Applicable cylinder bore size (mm) 1.5 MPa 1 MPa 0.1 MPa Proof pressure Max. operating pressure Body swivels 360 Swivel type allows free setting of piping.
A MPa ON kPa OUT1 OFF OUT2 CH 1 2 3 4 PRESSURE Min. B Released SET Work 1 Work 2 Work n Atmosphere Max. A: Maximum pressure value when work piece is adsorbed. A B 4 ON = A A B 4 SET OFF = B + Min. B: Minimum pressure value when work piece is not adsorbed. OUT1 auto preset For adsorption verification: In this mode, repeat the adsorption and release of the work piece for a few times.
AN120-M5 KJS04-M5 VQZ200/2000 KQ2S06-01S INA-25-46 IN-457-32(6 ) VQZ300/3000 KQ2H08-02S AN101-01 KQ2H06-01S 3 3 3 3 VQZ VQZ VQZ VQZ 82 82 82 82 ,N.C.
) r 0 6 l27l 1 2 6 (32\ 1 4 2 136t 1.20 30 5, , 2 4 (6) Millimoters in Parentheses Millimetec in Parenlheses NVFil2so-N024 NVFIrt250-N02-36 F O_F.. 5.07lbs. (2 3 Ks) T T '75 PSIG (5 Kgt/cm2) A H c D tr F u H J K M N o 6 6 8 160 6\ 5 4 6 138 6) 1 5 7 (40) 1 2 2 (31) 0 0 6 (1 5) o 1 2 (3) 0 9 4 23 9) 1 5 7 (40) 1 0 6 (271 1 4 2 (36) 1 2 6 t32\ 1 2 0 30 5) , 2 t (6) A B D E F G H J K M N 6 8
) r 0 6 l27l 1 2 6 (32\ 1 4 2 136t 1.20 30 5, , 2 4 (6) Millimoters in Parentheses Millimetec in Parenlheses NVFil2so-N024 NVFIrt250-N02-36 F O_F.. 5.07lbs. (2 3 Ks) T T '75 PSIG (5 Kgt/cm2) A H c D tr F u H J K M N o 6 6 8 160 6\ 5 4 6 138 6) 1 5 7 (40) 1 2 2 (31) 0 0 6 (1 5) o 1 2 (3) 0 9 4 23 9) 1 5 7 (40) 1 0 6 (271 1 4 2 (36) 1 2 6 t32\ 1 2 0 30 5) , 2 t (6) A B D E F G H J K M N 6 8
effective thread depth G Q Q R D R H E E 4-K through 8-L counter bore 4-K through C B + Stroke J J 8-L counter bore A + Stroke M M CHKDB20 & 25 CHKDB32 to 100 Width across flats f c a b g e h + Stroke Rod end male thread (mm) F L A B C D E G H J K M P Q R Bore size (mm) 20 M8 x 1.25 9.5 depth 5.4 51 43 8 12 10 10 6 30 5.5 43 1/8 16.5 6 25 M10 x 1.5 9.5 depth 5.4 53 45 8 14 12 12 6 36 5.5
4" one-touch fitting) M5 0.8 1/8 NPTF Port size M5 0.8 A port X port Note1) M5 0.8 M5 0.8 M5 0.8 Body ported type SYJ5 2/SYJ5 2R 3.4 (0.19) Note 2) Valve effective area mm2(Cv) M5 : 3.3 (0.18) 1/8 : 4.8 (0.27) N3T, N7T: 3.8 (0.21) Base mounted type SYJ5 4/SYJ5 4R M5 : 3.8 (0.21) 1/8 : 4.7 (0.26) Note 1 : Only for external pilot Note 2 : Value when used on a manifold Proper Combinations of