PFM5.eng Blue DC(-) DIN rail mounting (using ZS-33-R ) Mount the DIN rail mounting parts using DIN rail mounting screws and joint screws supplied. The required tightening torque of the DIN rail mounting screws and joint screws is 0.40.05 Nm. Connector for electrical connections.
Spring washers L K Connector pin numbers Wire colour Description S L Function selection mode Joint screws J M 1 Brown DC(+) M DIN rail mounting screws Danger: DANGER indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. In measurement mode, press the S button for 2 seconds or longer, to display [F 0].
Colour Content Caution Brown DC(+) Black OUT( Analogue output) Do not touch the terminals and connectors while the power is on. Otherwise electric shock, malfunction or damage to the product can result. Blue DC(-) After maintenance is complete, perform appropriate functional inspections and leak tests.
Input of the Set point 2 L/min, L CFM x 10-2, CFM x 10-1, ft3 x 10-2, ft3 x 10-1, gal(US)/min, gal(US) 1 Brown DC(+) Non-Reverse output Reverse output Refer to the product catalogue or SMC website (URL http://www.smcworld.com) for more information about panel cut-out dimensions.
When the Upper temperature limit alarm and the DC power voltage alarm go off simultaneously, D2 will be 23X1+22X0+21X0+20X1=9(=39H). HEC 4-4 Details of Communication Format 4-6 Reading temperature average data Note) For this product, the average temperature data, Tm, indicates the temperature of the external sensor.
PID parameters are set incorrectly. setting Cause / Measure DC output voltage of product is reduced. Check the power voltage. Code Description Manner of reset ERR19 Abnormal auto tuning alarm Stop Overloaded during auto tuning mode Avoid overload. ERR02 System error 2 Stop The FRAM data was destroyed by highlevel noise.
Current limiting Power supply current Power supply voltage for pulse signal resistor R type limiting resistor 24V DC 10% 3.3k 5% (0.5W or more ) LEC-PA-R-332 5 VDC 5% 390 5% (0.1W or more ) LEC-PA-R-391 NPN type (LECPAN-) Power supply for pulse signal Inside of the driver Positioning unit side NP+ <3> 1k NP<4> 120 Current limiting resistor R PP+ <5> 1k PP<6> 120 Current limiting resistor
Connector 9 - (6) Power supply Supply power 24V DC. Caution Supply power first to the controller (LEC), then to the gateway unit. If power is supplied to the gateway unit and then to the controller (LEC), reset the data link after supplying power to the controller (LEC). (Refer to 12.4 Gateway unit control flag for the details of data link reset.)
Locking position 8 -
Maintenance Caution
The leakage current should be 5% or less (AC coil) or 2% or less (DC coil) of the rated voltage. 2. Use in low temperature environments Protection against freezing or solidification of impurities etc. When heating the valve body and piping by a heater, etc., be careful not to heat the coil with the heater. 4 Installation Warning 1.
When the wires are to be installed in the control panel along with those for other types of equipment, make sure to separate the AC and DC lines (to prevent the risk of damaging the elements in the circuit due to noise). Twisting the AC lines together is an effective countermeasure against noise. 5.
Caution Manifold Mounting When the DC power supply is shut off, by the emergency breaking circuit for example, valve misoperation may occur due to surge voltage produced by other electrical parts (such as electromagnetic coils).
Supply 24 V DC to each of them. Power can be supplied from a single power supply or from separate power supplies. It is not necessary to connect the SW power supply when not using an input block. : When a single power supply is used, the voltage range of each power supply should be noted. SW power is supplied to the sensor connected to the input block.
Open the cover and set the address using an AS-Interface address programming device and DC power jack cable etc. (PEPPERL + FUCHS: VAZ-PK-V1-Cinch, SIEMENS: 3RK1901-3HA00 etc.) The Address assignment range is 1 to 31. The address can be set regardless of connecting order, but it is not possible to set address overlap. The address at shipment from the factory is 0.
Polarity Excessive tightening may damage the thread portion When connecting power to a solenoid valve with a DC specification and a light or surge voltage suppressor, check for polarity. If there is polarity, take note of the following.
Wiring Meaning Connector pin number Wiring colour 1 Brown Power supply DC(+) 2 White Analogue current output/Analogue voltage output 3 Blue Power supply DC(-) 4 Black IO-Link/Switch output (C/Q) Wiring specifications M8 Connector pin assignment M12 Connector pin assignment -11No.D-S-OMU0002-A Setting Initial settings are as follows: Switch output: Low (NPN = ON, PNP = OFF), Analogue output
Power supply (Valve) 24V DC -5% to +10% Current consumption Communication power supply 0.1A or less (24VDC) Enclosure IP20 Weight 80g or less CompoBus/S system specification Item Specification Applicable PLC OMRON Coop.
Therefore, when it is continuously energized or the energized period per day is longer than the de-energized period use a DC specification valve. For applications such as mounting a valve on a control panel, incorporate measure to limit the heat radiation so that it is within the operating temperature range.
Keep residual voltage leakage to 3% or less of the rated voltage for DC and 8% or less of the rated voltage for AC. Mounting Caution All models 1. In high humidity environments, keep the valve packed until the time of installation. 2. For models with switches, secure the lead wires so that they have sufficient slack, without any unreasonable force applied to them. 3.
DC output voltage of product is reduced. 1 Serial communications RS-232C / RS-485 RS-232C, RS-485 RS-232C ERR11 DC power supply failure Stop When no input is made within 1 minute regardless of setting mode, the A Power switch H Communication connector The fans at the power supply stops.