M Series Caution (1) Install an air filter. Install an air filter at the upstream side of valve. Select an air filter with a filtration degree of 5m or finer. (2) Install an aftercooler, air dryer or water separator, etc. Compressed air containing a large amount of drainage can cause the malfunction of pneumatic equipment.
Assembly,handling,repair and element replacement of pneumatic systems should be performed by a knowledgeable and experienced person. (1)Install an air filter. Install an air filter upstream near the valve.
Low temperature operation 1) The valve can be used in an ambient temperature of not less than 5C.
If the product is an external type pilot, it is not splash proof. Be careful not to expose it to any fluid when maintaining the valve. When replacing a valve, if an external pilot solenoid valve is mounted in the wrong direction, it may malfunction or leak air.
(control operation) LC3F2 Command an operation in the reverse direction only after a cylinder rod stopped completely. LC3F2 Do not operate a cylinder rod with an external force when the electric cylinder directional control driver is turned off or output is in the off state.
Resistance of equipment in the Use components and equipment of an appropriate size. It affects the piping diameter and length. Equipment at the exhaust side should also be of an appropriate size. Refer to the catalog and operation manual of the components and equipment for details. piping route is too large 3.
If using the product in an interlocking circuit: Provide a double interlocking system, for example a mechanical system. Check the product regularly for proper operation Otherwise malfunction can result, causing an accident.
If any of the examples below are applicable, there may be an internal problem with the valve.
If the compressed air supply includes chemicals, synthetic materials (including organic solvents), salinity, corrosive gas, etc., it can lead to damage or malfunction. 2) Install an air filter. Install an air filter at the up stream side to the valve. Filtration degree should be 5 m or less. 3) Install an air dryer, after cooler, etc.
Select a fitting with an I.D. greater than 8 for the VP344 and the VP342; more than 10 for the VP544 and VP542, and more than 12 for VP744 and VP742 when piping length is less than 3 meters. Use an external pilot when there is a small flow outlet of the valve.
1% F.S.30 msAir/Inert gas0 to 50C (With no condensation)0.88 MPa0.05 MPa to supply pressureSet pressure to 0.88 MPa (VY1 01)1 to 5 VDC, 0 to 10 VDC, 4 to 20 mA DC, 0 to 20 mA DC12 VDC ? 10%, 24 VDC ? 10%, 1.8 W or lessDIN terminalCable O.D. ?
1% F.S.30 msAir/Inert gas0 to 50C (With no condensation)0.88 MPa0.05 MPa to supply pressureSet pressure to 0.88 MPa (VY1 01)1 to 5 VDC, 0 to 10 VDC, 4 to 20 mA DC, 0 to 20 mA DC12 VDC ? 10%, 24 VDC ? 10%, 1.8 W or lessDIN terminalCable O.D. ?
1% F.S.30 msAir/Inert gas0 to 50C (With no condensation)0.88 MPa0.05 MPa to supply pressureSet pressure to 0.88 MPa (VY1 01)1 to 5 VDC, 0 to 10 VDC, 4 to 20 mA DC, 0 to 20 mA DC12 VDC ? 10%, 24 VDC ? 10%, 1.8 W or lessDIN terminalCable O.D. ?
Bore size 4.5 6 8 MXJ Symbol 4 6 8 Stroke Metal stopper on both ends 5, 10 5, 10, 15 5, 10, 15, 20 Switch rail Functional option MXP Without option Axial piping type Nil P Nil N With magnet and switch rail Without magnet and switch rail MXY Note) Use an optional stepped positioning pin (see page 175) because the positioning pin hole of this product goes through.
Because suctioned matter is ejected together with exhaust, do not direct an exhaust port at a person or equipment. AFJ AMV 2.
Stroke and Weight Bore 8 12 16 20 8 Stroke(mm) 12 16 20 Short 65 155 350 645 Weight(g) Stroke variations 16 24 32 40 Stroke(mm) Middle 85 190 445 850 Weight(g) 32 48 64 80 Stroke(mm) Long Short 120 275 650 1225 Weight(g) Middle Long Holding Force Bore * 8 12 16 20 Holding Force 19 48 90 141 *)1.Holding Force per finger 2.Working Pressure: 0.5MPa, Holding force for stroke center value with
Combination Spacer Select one of the spacers below when connecting to an F.R.L. combination unit (AC2000 to AC6000). (Spacers must be ordered separately.)
Further, give nut an additional 1 turns with appropriate wrench or the like.Leave 0 space between the screwed-in nut and the tube in-line with the tube axis. If tightened insufficiently, nut may be loosened and it may cause the air leakage or tube coming off. When using soft copper tube, first tighten the nut by hand and then give it an additional one turn with wrench.
Tamper Proof Speed Controller with One-touch Fitting Elbow Type/Universal Type Series AS1F-T RoHS Model Able to adjust flow by a special tool Prevention of an unnecessary manual operation Applicable tubing O.D.