Angular Style Air Gripper Series MHC2/MHCA2/MHCM2 Use this as a standard when mounting, etc.
It is dependant upon whether a load is connected with the positive or negative side. These switches are known for high speed response, longevity, and they can reduce wiring work. Voltage drops at the value of r x I. PS1000, PS1100 Caution 1 to 5 [V] Current I Lead wire resistance r The load current range for a PS1000 and PS1100 is between 5 [mA] to 40 [mA].
Piping 01/N01 A B D ZS-24-A ZS-24-B ZS-24-D ZS-35-C ZS-35-D ZS-35-F ZS-35-G Bracket A Bracket B Bracket D E E Panel mount adapter Panel mount adapter + Front protective cover F W1/WF1/M5/C4/C6 Output specifications R T S V X Y NPN open collector 2 outputs + Analog voltage/Auto-shift switching PNP open collector 2 outputs + Analog voltage/Auto-shift switching NPN open collector 2 outputs +
Caution 4 XSA-OMS0001-A (5) Leakage voltage Particularly when using a resistor in parallel with a switching element and using a C-R element (surge voltage suppressor) to protect the switching element, take note that leakage current will flow through the resistor, C-R element, etc., creating a possible danger that the valve may not turn off. passes through the C-R device.
Therefore, make sure to use a pressure regulator to convert line pressure into supply pressure for the actuating valve and the brake valve. In order to actuate multiple cylinders at once, use a pressure regulator that can handle a large air flow volume and also consider installing a surge tank.
(Same surface) Hs 22 B A D-A93 24.5 10.5 16.5 50 50 50 D-M9B D-M9BW D-B54 50 50 75 Auto Switch Mounting Position and Its Height Unit: mm 8.5 Auto switch set value and its height 63 7.5 30.5 47 11.5 34.5 47 2 25 50.5 Auto switch Symbol 40 11 23.5 34.5 15 27.5 34.5 5.5 18 38 50 7.5 30.5 40 11.5 34.5 40 2 25 43.5 A B Hs A B Hs A B Hs D-B54 D-A93 Hs B A 33 D-M9B D-M9BW D-B54 12 Note 1) The
When there is a large amount of drainage Compressed air containing a large amount of drainage can cause the malfunction of pneumatic equipment. An air dryer or water separator should be installed upstream from filters. Connection thread size Proper tightening torque (R, NPT) (Nm) 1/8 3 to 5 3.
Therefore, supply pressure regulated by a built-in regulator e passes through the air supply solenoid valve q and is applied to the pilot chamber r. The pressure in the pilot chamber r increases and operates on the upper surface of the diaphragm t. As a result, the air supply valve y linked to the diaphragm t opens, and a portion of the supply pressure becomes output pressure.
A A B (mm) D-A9V D-A9 D-M9 D-M9W D-M9V D-M9WV A B A B Bore size (mm) W Hs A B W A B Hs 32 40 50 63 12 [17] 9 1 12 [17] 9 29 8 [13] 5 3 (0.5) 8 [13] 5 27 16 11.5 1.5 16 11.5 32.5 12 7.5 5.5 (3) 12 7.5 30.5 14 <19> 14.5 4.5 14 <19> 14.5 42 10 <15> 10.5 8.5 (6) 10 <15> 10.5 36.5 16.5 17.5 7.5 16.5 17.5 42 12.5 13.5 11.5 (9) 12.5 13.5 40 [ ]: Values for 5 mm stroke with 32 < >: Values for 10
When used as a switch output device Setting of NPN open collector 2 outputs Setting of PNP open collector 2 outputs Brown DC(+) q Brown DC(+) q Load Black OUT1 r Black OUT1 r Load Main circuit Main circuit + + 12 to 24 VDC 12 to 24 VDC White OUT2 w White OUT2 w Load Load Blue DC() e Blue DC() e When used as an IO-Link device Brown L+ q L+ Black C/Q r Main circuit C/Q IO-Link master White
Leakage voltage Particularly when using a resistor in parallel with a switching element and using a C-R element (surge voltage suppressor) to protect the switching element, take note that leakage current will flow through the resistor and C-R element, etc., creating a danger that the valve may not shut OFF.
By chamfering as shown in the following table, machining of threads is easier and effective for burr prevention. 2Specific Product Precautions5 Caution (2) Connection thread: R, NPT First, tighten the fitting by hand, then use a wrench appropriate for the hexagon flats of the body to tighten it a further two or three turns. For a tightening torque guide, see the table below.
(Representative valve) Ambient and operating air temperature -5 to 60 oC (No freezing) C(dm3/(sbar)) 0.6 [1(P) 2(A)] , 0.5 [2(A)3(R)] Flow rate characteristics b 0.2 [1(P) 2(A)] , 0.15 [2(A)3(R)] Port size Rc, NPT, G1/8 ON timing ON upon the set delay Output method Normal close Reset Resets by exhausting the input signal pressure Weight 480g *) The dispersion is shown excluding the first
Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Caution: Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Warning: Danger : Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.
Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Caution: Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Warning: Danger : Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.
How to Mount a Compact Slide A compact slide can be mounted from 4 directions. Make a selection suitable for the applicable machinery and workpieces, etc.
Caution Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. Warning 1.
OUT IN BUS COM A COM B COM C COM D F R P B U S O I R DIA BF SOL RUN GATEWAY UNIT EX500 SERIES 18 19 Switch setting Open the station number switch protective cover and set the switches with a sharp-pointed watchmakers screwdriver etc. NOTE 1. Be sure to turn off the power before setting the switches. 2. Be sure to set these switches before use.
When a workpiece could be deformed during adsorption or transportion. (Example of a cardboard box) When the adsorption surface of a workpiece is slanted.
14 16.5 1.0 Allowable moment coefficient 0.7 0.5 Note) For A, A, A and A, there is no difference in the corrected values due to the stroke.