MK ML2B ML1C REA REC Installation and Adjustment/ Regarding Clamp Arm Removal and Reinstallation RHC MTS q During the removal or reinstallation of the clamp arm, make sure to use a wrench or a vise to secure the clamp arm before removing or tightening the bolt.
Auto Switch Precautions q Design & Selection Warning In the same way, when operating under a specified voltage, although an auto switch may operate normally, the load may not operate. Therefore, the formula below should be satisfied after confirming the minimum operating voltage of the load. qConfirm the specifications.
(mm) Electrical entry P Port size B C D E F H K L M N A Grommet: G Conduit: C Conduit terminat: T Model Q R Q R Q R S U 13.5 28 64 31 6.5 12.5 28 14 12.8 M4 4.5 22 59 44 50 99 50 66 83 1/8 VCS21 18 36 67.5 31 8.5 12.5 28 18 12.8 M4 6 22 62 44 53 99 53 66 86 1/4 22 40 81.5 36.5 11 15 32 20 19 M5 8 24 76 46 66.5 101 66.5 68 99 1/4, 3/8 VCS31 30 50 86 36.5 13.5 15 32 25 23 M5 8 24 80 46 71 101
39 39 41.5 Q 23 23 25.5 N 61 (68) 69 (76) 79 (89) d 47 52 57 a 34 51 58 N 69 (76) 77 (84) 87 (97) N 61 69 79 c 65 78 86 Q R 57 74 81 VXP2142 , 30 30 35 20 20 23 34 43 47 29 37 43 28 35 40 3 8 8 63 80 90 59 59 62 104 (116) 118 (136) 133 (150) 26 32.5 36.5 71 87 97 14 17.5 20 92 92 95 3 8 1 2 3 4 1 VXP2152 VXP2262 VXP2150 VXP2260 ( ): N.O. 17-3-50 9 Series VXP21/22/23 Pilot Operated 2 Port
0 Description Shield plate Switch ass'y Piston PT fittings Adjustment screw Pointer Spring Scale plate Miniseal Y type Magnet No. q w e r t y u i o !
Home position switch De-energized operating type 0.1 Nm 24VDC 5% 5W (at 75C) Model Static torque Rated voltage Power consumption Brake specifications LC6D-220AD-Q (Refer to page 306 details.) LC6D-507AD-Q (Refer to page 306 for details.) Applicable driver Holding plate: MB1(1 pc.), Phillips countersunk head screw M3 x 6l (1 pc.)
6 y u q !5 !8 i e !7 !4 t !9 !0 !2 w !1 o @0 @1 Built-in magnet @2 @5 @3 @4 Component Parts No. Description Material Qty. Note No. Description Material Qty.
For connector cable of M8 connector, refer to back page 10. 25 Series SYJ5000 Construction 2 position single 2 position double (A) 4 (B) 2 (A) 4 (B) 2 5 (R1) 3 (R2) 1 (P) 5 (R1) 3 (R2) 1 (P) e w q t r q y t rw (A) 4 (B) 2 (A) 4 (B) 2 i 5 (R1) 1 (P) 3 (R2) 5 (R1) 1 (P) 3 (R2) i u 3 position closed center/exhaust center/pressure center 3 position closed center (B) 2 (A) 4 q t rw 5 (R1) 3 (R2
Exploded view q r How to Calculate the Flow Rate u For obtaining the flow rate, refer to front matters 44 to 47. t y e o i o Magnifying figure Self-up screw 2 1 3 1504
Display Description t Power supply ON/servo ON :Green turns on q q PWR Power supply LED Power supply ON/servo OFF :Green flashes y w With alarm : Red turns on w ALM Alarm LED Parameter setting : Red flashes Change and protection of the mode SW (Close the cover after changing SW) u i e Cover o !0 Frame ground (Tighten the bolt with the nut when mounting the controller.
w e r t y u i o q Rated pressure range w Output specification u Option 2 * Note that the optional parts that can be used vary depending on the piping direction.
Material Description q Rod cover A Clear hard anodized Aluminum alloy Data w Rod cover B Clear hard anodized Aluminum alloy Set of the nos. !1, !2, !3, !
Component Parts No. q w e r t y u No. i o !0 !1 !2 !3 !
6 q e r t !5 w !4 !0 u y 32 to 50 With auto switch (built-in magnet) !6 q e r t !5 i o !1 !3 !2 !7 w !4 !0 u y Description No.
Home position switch De-energized operating type 0.1 Nm 24VDC 5% 5W (at 75C) Model Static torque Rated voltage Power consumption Brake specifications LC6D-220AD-Q (Refer to page 306 details.) LC6D-507AD-Q (Refer to page 306 for details.) Applicable driver Holding plate: MB1(1 pc.), Phillips countersunk head screw M3 x 6l (1 pc.)
u r y e w e y q y u r y e w u i t q i t q i t q r y e w AS e w q w ASP o Free flow Female thread Male thread ASN Free flow One-touch fitting Male thread AQ ASV AK Component Parts ASS Description Material Note No.
Description Material Aluminum die cast Aluminum die cast Top cover Bottom cover q w No.