EX600-SDNA_eng (Default setting) 8 7 Configuration Mode Address X1 9 6 x10 x1 2 1 0 0 5 Mark C on the unit Mark B at cable end Mark A at cable end 4 Address 1 9 4 3 1 0 : : (1) 2 3 Input data + System diagnosis + Unit diagnosis (Up to 10 units) Input data + System diagnosis Input data only (Default setting) 8 7 9 6 6 Content 3 4 1 2 0 5 Content 5 0 (Default setting) 4 1 2 3 Node Address Data Rate 8 7 PGM
') 1 IN 295 589 844 1 1 7 8 1473 1767 2062 2356 OUT 314 628 942 1257 '1571 1885 2 1 9 9 2513 Enclosed Spring Eorces t,1*ill", ' Fgs!
') 1 IN 295 589 844 1 1 7 8 1473 1767 2062 2356 OUT 314 628 942 1257 '1571 1885 2 1 9 9 2513 Enclosed Spring Eorces t,1*ill", ' Fgs!
3 o @1 @0 !1 !0 !2 r w i e !5 !9 y u t MDHR3 !4 !3 q !1 @0 @1 w o e i MHZ2 !5 MHZJ2 MHQ r !7 !6 t !0 !8 !2 i !9 y u MHL2 Component Parts Component Parts MHR No. !2 !3 !4 !5 !6 !7 !8 !
Material LMU100 LMU200 Description Mist spray body 1 Platinum silver coated Aluminum die-casted Mist spray tank Body seal 3 2 81021-3 Platinum silver coated Aluminum die-casted NBR 1 Element 4 81021-6 Bronze 1 Lubrication plug 5 81021-7 Brass 1 Filler seal 6 81021-8 1 Level gauge 7 Hard glass 81021-9 1 Type C retaining ring for hole 8 Stainless steel FG00193 1 O-ring 9 FKM KA00622 2 Pressure
R Q2 B P C F(h9) D G1 G2 J K L M N Q1 E(g6) Q3 Model A 90 180 270 M5 M3 CRB1BW10-lS CRB1BW10-lSE CRB1BW15-lS CRB1BW15-lSE CRB1BW20-lS CRB1BW20-lSE CRB1BW30-lS CRB1BW30-lSE 3.4 (5.5) 5 8.5 5 11 9 14 10 15.5 25 9.5 25 10 25 13 25 14 M3 (6) 0 0.036 15 24 8 0.004 0.012 9 14 3 1 5 9 0.5 29 4 M3 M3 (5) M5 M3 3.4 (6) M3 (10) 0.004 0.012 0 0.043 20 29 9 12 18 5 4 1.5 6 10 0.5 34 M3 M4 (7.5) 4.5
Selection procedure 1. First find the ratio of the discharge rate for fresh water when viscosity is 100mPas from the graph at the left. It is determined to be 45%. 2. Next, in the required specification example the viscosity is 100mPas and the discharge rate is 2.7l/min.
However, there is no problem in terms of contact output, when an output signal exceeds 1 mA or more.
Rc 1 4 1 4 1 4 NPT G Y F02 Body option 1 0 Internal pilot type External pilot type Twist selector (2 position) Key selector (2 position) Note 1) When selecting the flush type, it is not necessary to select the suffix for the actuator.
1 For the remote type monitor unit, only the front side is IP65 compliant.
5.5 2.5 5.5 3 1 1 6 10 15 20 25 32 20.5 27.5 38 50 50 60 4.5 7.5 4.5 7 9 9 Note 1) Negative figures in the table D indicate how much the load wires protrude from the cylinder body.
returned when the following request message is received. 1) When unspecified function code is used. 2) An address out of range is specified. 3) The data field is not normal.
t 8 Embedded pressure gauge is a standard teature (HNBB) lmproved relief '1.
HHH is 6 displayed. (1) Reset applied pressure (1) Check that the pressure is not to a level within the set pressure range.
Load Load Switch 1 Switch 1 Blue [Black] Blue [Black] Brown [Red] Brown [Red] Switch 2 Switch 2 Blue [Black] Blue [Black] Internal voltage drop Power supply voltage Leakage current Load impedance Load voltage at OFF = x 2 pcs. x = 1mA x 2 pcs. x 3k = 6V = 24V 4V x 2 pcs. = 16V Example: Power supply is 24VDC Internal voltage drop in switch is 4V Example: Load impedance is 3k Leakage current
Symbol In the symbol ( ), when the valve is closed, flow is blocked from port 1 to port 2. However, if the pressure in port 2 is higher than port 1, the valve will not be able to block the fluid and it will flow from port 2 to port 1. 1.
HHH is 6 displayed. (1) Reset applied pressure (1) Check that the pressure is not to a level within the set pressure range.
An over current Incorrect internal data processing of the product (Er0, 4, 6, 7, 8 or 9) (1) Check if there is noise interference error (Er1, 2) is displayed. (such as static electricity. (2) Check if the power supply voltage System error is in the range 24 VDC 10%. (Er0, 4, 6, 7, 8 or 9) is displayed. (2) Supply power in the range 24 VDC 10%.
The brown lead wire is (+) and the blue lead wire is (). 1) If connections are reversed, a switch will operate, however, the light emitting diode will not light up. Also note that a current greater than that specified will damage a light emitting diode and it will no longer operate. Applicable models: D-C73, C73C D-B53, B54 1. Do not drop or bump. 1.
MY1 Air cushion is standard Impact absorption is possible at the highspeed stroke end.