Series CM2-Z 10-/11- ø20, ø25, ø32, ø40 21-/22- Air Cylinder , 350, 400, 450, 500, 600, 700, 800 12-REA40 12-REA50 50 1300 Non-lube 200, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000 63 12-REA63 Note 1) Stroke exceeding the standard stroke but below the maximum manufacturable stroke is available as special orders.
Description Long 500 420 3 0.52 to 1.63 80 160 IF32 IF31 IF30 Long 1,000 800 4 0.61 to 1.91 160 320 Cover q SPCD SPCD 12 ADC Mounting plate SPCC Stainless steel 304 Stainless steel 304 w Long 1,800 1,450 5 0.69 to 2.23 280 560 Bellows e r PBP or Stainless steel 304 Long 2,600 2,000 6 0.70 to 2.28 400 800 Body C3604B or Stainless steel 304 ON-flow: Flow volume under which a microswitch starts
.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com 0.1 0 VX211 VX22 VX23 VX2 4 VX2 5 VX2 60-02 VX2 602 50 100 150 200 250 300 350 3 100 200 300 400 500 600 4.5 200 400 600 800 1,000 1,200 3 2 3 2 3 2 3 2 03 04 6 500 1,000 1,250 8 500 700 900 10 500 700 900 10 700 1,000 Flow rate Q l/min (ANR) How to read
For R, NPT Thread (With sealant) Tightening method 1. The proper tightening torques of the fittings are as shown in the table below. As a guide, tighten it by hand, then turn it two or three turns with a wrench. Check the dimensions of each product for the hexagon width across flats.
Flow direction (Right Left) Nil Rc1/4 F G1/4 *1 Nil Flow direction (Left Right ) R Flow direction (Right Left) *1: Conforming to ISO16030 *1: Conforming to ISO16030 Square embedded type pressure gauge Round type pressure gauge Refer to the WEB catalog for details.
Therefore, supply pressure regulated by a built-in regulator e passes through the air supply solenoid valve q and is applied to the pilot chamber r. The pressure in the pilot chamber r increases and operates on the upper surface of the diaphragm t. As a result, the air supply valve y linked to the diaphragm t opens, and a portion of the supply pressure becomes output pressure.
Configuration One thermo-chiller for one master. 2 2 R D R D 3 3 S D S D 5 5 S G S G Master This product Do not connect any wire to other PIN numbers. Fig. 3-13 Connection of RS-232C HRL Series 3.3 Installation 3-27 HRX-OM-W060 Chapter 3 Transport and Setting Up 3.4 Piping Connect piping firmly.
For details, refer to the IDK series in the Best Pneumatics No.6. 705 MHY2 Series Construction Closed condition 10 16 20, 25 r o !8 e w !7 t !5 r o !8 e !6 w @0 !7 t !5 r o !8 e !6 w @0 !7 t !5 !0 u !2 i q !1 !4 y !9 !0 u !2 i q !1 !4 y !9 !0 u !3 !2 i q !1 !4 y !9 Open condition Component Parts Note No.
Flow direction Right Down With element service indicator AMP220 Rc NPT AMP320 AMP420 G 2 Exhaust Cleaner for Clean Rooms Series AMP How to Order AMP 2 0 2 03 Optional specifications Body size None Flow direction RightDown With element service indicator Nil R T 2 3 4 1/4 standard 3/8 standard 1/2 standard Element construction Accessories (optional) Nil None 2 2 stage B With bracket
Flow direction Right Down With element service indicator AMP220 Rc NPT AMP320 AMP420 G Features 1 Exhaust Cleaner for Clean Rooms Series AMP How to Order AMP 2 0 2 03 Optional specifications Body size None Flow direction RightDown With element service indicator Nil R T 2 3 4 1/4 standard 3/8 standard 1/2 standard Element construction Accessories (optional) Nil None 2 2 stage B With
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com d n i n i W g c e t i r o i d n e p a t e p i P Leakage Voltage It must be noted that when connecting C-R element parallel to switching element, leakage current flows through C-R element and the leak voltage increases
Nil R L Motor straight, motor cable, switch and switch rail located on the right Photo micro sensor rail 1 pc. Motor straight, motor cable, switch and switch rail located on the left Proximity switch rail 1 pc. The tables above show the definition for each symbol only and cannot be used for actual model selection. 1
OUT IN BUS COM A COM B COM C COM D F R P B U S O I R DIA BF SOL RUN GATEWAY UNIT EX500 SERIES 18 19 Switch setting Open the station number switch protective cover and set the switches with a sharp-pointed watchmakers screwdriver etc. NOTE 1. Be sure to turn off the power before setting the switches. 2. Be sure to set these switches before use.
Pilot port location Nil Front R Right L Left Pilot port Pilot port Pilot port Front Right Left Application Examples Lightweight workpieces such as electronic boards can be stopped, positioned and clamped with high accuracy. Stopper Positioning Clamping Space is reduced due to the integrated construction of a cylinder and linear guide.
The used of turbine oil at temperatures lower than 0C leads to increased viscosity and may cause the valve to malfunction. d n i n i W g c e t i r o i d n e p a t e p i P Leakage Voltage It must be noted that when connecting C-R element parallel to switching element, leakage current flows through C-R element and the leak voltage increases. 2 thread to be left exposed Clamping Torque Switching
CJ2-Z Series 10, 16 Air Cylinder 10-/1121-/22RoHS How to Order Cushion Clean series 10 11 Relief type Vacuum suction type Rubber bumper (Standard) Air cushion Nil A 10 D L 16 60 A R C J 2 M9BW Z B 21 D L 16 60 R C J 2 M9BW Z B Number of auto switches Nil Built-in magnet Head cover port location 2 pcs. 1 pc. n pcs.
(Top view) r r e Pressure gauge unit 2) Code Unit psig/bar MPa w q w q w q 1) Refer to gauge guide (P.1058) for gauge specifications.
This is a legacy product. Please contact us for the latest version.sales@ocaire.com