C95 (When port sizes for A, B ports are mixed, indicate C4 or C6 in cell .)
At piping This is equivalent to a magnetic field of approximately 18cm in radius from a welding area using a welding current of almost 15,000 amperes. To use the system in a magnetic field that exceeds this value, use a magnetic material to shield the sensor unit Foreign matter should not enter. Entering of foreign matter will cause malfunction.
t r r , " . . a : r i . . . , r i a , r . .
Caution Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. Warning 1.
t r r , " . . a : r i . . . , r i a , r . .
Then, a correct operation works until a vacuum pressure proportional to the input signal is reached, and a vacuum pressure is obtained which is always proportional to the input signal.
ZX B B' A B ZR A B P1 A A' ZM !0 o r t ZH ZU Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com e ZL ZY ZQ ZF ZP !1 ZCU Section A-A' (Ejector) AMJ !
Nole 5) When mounting a blanking plate and lhe regulator with diflerent pressure set. olease inlorm SI C ol the oder ol a manifold stalion beside a purchase order, Nole) Refer to the table below tor possible mixed combination, Uod.l rvl03tr tTvl05tl tw201tr rTv203tr tw205tr tw10ltr o tw103tr o a a o tTV't05tr o o a a trv20ttr o o tTV203tr o o a a tTV205tr o o a o Pressure response wilh no
Caution Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. Warning 1.
When tightening the auto switch mounting screw, use a watchmakers screw driver with a handle diameter of about 5 to 6mm. Furthermore, use a tightening torque of 0.05 to 0.1 Nm. As a rule, it should be turned about 90 from the point at which tightening can be felt. Use a tightening torque of 1 to 1.2 Nm for the hexagon socket head set screws (M4 x 0.7). 1.
Piping specification: -02 and -N02 After hand tightening, tighten the fitting using a spanner on the flat surfaces of the fitting. The tightening torque must be 8 to 12 Nm.
L32 pin clamp cylinder available O Compact design makes it applicable to a broad range of workpieces. OContributes to a lightweight jig.
If a directional switching valve (solenoid valve, mechanical valve, etc.) is mounted on the supply side of the regulator and repeatedly switched ON and OFF, wear of the nozzle/flapper section will be accelerated and a discrepancy in the setting value may occur. Therefore, avoid using a directional switching valve on the supply side.
M E N S I O N S AD S E R I E S A U I T O D R A I N S S Y M B O L S H O W T O O R D E R A U T O D R A I N S E R I E S AD AD402-02 (1/4) PT AD402-03 (3/8) PT AD402-04 (1/2) PT AD600-06 (3/4) PT AD600-10 (1) PT H O W T O O R D E R A U T O D R A I N S E R I E S NAD NAD402-N02 (1/4) NPT NAD402-N03 (3/8) NPT NAD402-N04 (1/2) NPT NAD600-N06 (3/4) NPT NAD600-N10 (1) NPT FOR FURTHER TECHNICAL DETAILS
8 A 8.1 8.2 A (10) 8.3 8.4 IDF60-20-A IDF60-30-A IDF70-20-A IDF70-30-A IDF80-20-A IDF80-30-A IDF90-20-A IDF90-30-A 50Hz 2.3 4 5.8 7.1 3/min(ANR) m 60Hz 3.2 4.8 6.5 7.9 10 1) ANR 65% 2) IDF60/70/80/90 Series 8-1 IDX-OM-W093 A 8.5 IDF60/70/80/90 Series 8-2 IDX-OM-W093 C 9 C 9.1 9.2 1) 2) IDF60/70/80/90 Series 9-1 IDX-OM-W093 A IDF60/70/80/90 Series 9-2 IDX-OM-W093 L 10 L L
As a guide, tighten it by hand, then turn it two or three turns with a wrench. Check the dimensions of each product for the hexagon width across flats.
D2 M1 L1 L2 T M5 type H (width across flats) Applicable tubing O.D. d A A4 D1 L3 D2 M1 L1 T L2 Model Weight (g) Note 2) Tubing O.D. d T H D1 D2 L1 L2 L3 M1 L4 Max.
Rc(PT) 12 04 o Bracket B o o Bracket o o @ L-bracket Connection NPTl/4 N02 a o Connection NPT3/8 N03 a o o tr 6 . 9 o u t = ^ O v o EL o Connection NPTl/2 N04 o Connection G(PD 1/4 F02 o o Connection G(PR 3/8 F03 o o Connection G(PR 1/2 F04 o O: Standard specifications O: Combination possible Blank: Combination not possible Modular Connection Part Numbers muxm : Air filter NAF3OOO NAF4OOO
5 15-17-5 6 Series AS-FPQ/FPG Dimensions H (width across flats) Applicable tubing O.D. d A L4 D1 L3 D2 M1 L1 L2 T M5 type H (width across flats) Applicable tubing O.D. d A A4 D1 L3 D2 M1 L1 T L2 Model Weight (g) Note 2) Tubing O.D. d T H D1 D2 L1 L2 L3 M1 L4 Max. Min. Max. 1 2 Min.