E-MY2_E_D 19.6 m/s2 Nominal size:16 5kg 1.25kg 10kg 2.5kg Maximum load weight NOTE2) Nominal size:25 20kg 5kg 10kg 2.5kg Acceleration and deceleration method Trapezoidal drive Moving direction Horizontal direction Positioning points Both ends (mechanical stoppers), 1 intermediate position Both ends 0.01mm Repeated Positioning stopping precision Intermediate stopping position 0.1mm Nominal size:16 10N
MIN. 3D [ n pes. of connection will result in n times of voltage drop] Piston speed limitation for intermediate stroke position Do not exceed max. piston speed when auto switch is at the intermediate stroke and a load is applied to the piston while traveling. Auto switch response time may be shortened due to insufficient loading operation as a result.
EEP-ROM 12 10 4. 3D No.PD16PD17 8 11 8 (2) 45 1. 55 0 55 2. ( 2.1) 3. 4. 5. 46 1. 40 0 40 2. 1. 2. 3. 3. 47 1. (2.6) 2. 3. 8 12 8 (2) 50 1 1. 1. 2. 3. 4. 5. 1 2. 2(51) 1. 2. 3. 1 3. 1. 12 2. 3. 4. 4. OFF 8 13 8 (2) 51 2 1. 2. 1. 2. 3. 4. 3. 1. 2. 3. 4. UVW UVW 5.
(PLC ) Alarm _Comment _061 (01-061) <> (1) ()1(ABS)2(INC) (2)PLC 15ms(30ms) 13.2[2](P.53) 3D B RESET (+)(-) Alarm _Comment _062 (01-062) (+)(-) 3E B RESET <> (01-096) C RESET <> -64- (01-097) <> C RESET <> <>OFF JOG OFF (01-098) OFF DRV C RESET <>ON (SVRE ON) DRIVE ON (01-099) <> SET OFF DRV C RESET <> <>12 (01-103) C RESET 1 [] A [a ] 2 [SW] [] A [a ] <> <>
For setting the holding force to be at least 20 times the work weight; Required holding force = 0.05kg X 20 X 9.8m/s2 = 10N min. 0 20 30 40 50 60 70 Holding point L (mm) When MHY2-16D is selected, the holding force is determined to be 13N according to the holding point distance (L = 35mm) and the pressure (0.6MPa).
In this case, loosen the screw with washer (3f) and place a lead wire (3d) into the bracket, and then re-tighten the screw. Caution DlN Terminal (Connection) The solenoid is wired with male terminals of DIN connector as shown below. Connect with corresponding terminals of the connector. Can be used as either + COM or COM.
In that case, loosen the screw (3f) and place a lead wire into the bracket (3d), and then tighten it once again. b) The maximum size for the round terminal (9) is 1.25 mm2 3.5 and for the Y terminal is 1.25 mm2 4. c) Cable (8) outside diameter: 6 to 12 mm Note) For the one with outside diameter ranged between 9 to 12 remove the inside parts of the rubber seal (7) before using. 3.
B RESET >+JOG (01-052) >+B RESET 65 - 112 12 0 2 3 4 5 6 7 Alarm _Comment _058 (01-058) 3A B RESET No.base PLC <> 1 1ABS 2INC 2PLC 2 14.2[2] (P.54) Alarm _Comment _061 (01-061) 3D B RESET <>+ <>+Alarm _Comment _062 (01-062) 3E B RESET <> (01-096) C RESET <> (01-097) <> C RESET <> <>OFF JOG OFF (01-098) OFF DRV C RESET <>ON SVRE ON DRIVE ON (01-099) <> SET OFF
In that case, loosen the self-up screw 3f, insert the lead wire into the bracket 3d and screw in the screw again. b) The maximum size of the crimped terminal 9 is 1.25mm2 to 3.5 for O terminal and 1.25mm2 to 4 for Y terminal. c) Use a cable with outside diameter of 6 to 12mm for the cable 8.
In that case, loosen the screw (3f) and place a lead wire into the bracket (3d), and then tighten it once again. b) The maximum size for the round terminal (9) is 1.25 mm23.5 and for the Y terminal is 1.25 mm24. c) Cable (8) outside diameter: 6 to 12 mm Note) For the one with outside diameter ranged between 9 to 12 remove the inside parts of the rubber seal (7) before using. 3.
In that case, loosen the screw (3f) and place a lead wire into the bracket (3d), and then tighten it once again. b) The maximum size for the round terminal (9) is 1.25 mm23.5 and for the Y terminal is 1.25 mm24. c) Cable (8) outside diameter: 6 to 12 mm Note) For the one with outside diameter ranged between 9 to 12 remove the inside parts of the rubber seal (7) before using. 3.
In that case, loosen the screw (3f) and place a lead wire into the bracket (3d), and then tighten it once again. b) The maximum size for the round terminal (9) is 1.25 mm2 3.5 and for the Y terminal is 1.25 mm2 4. c) Cable (8) outside diameter: 6 to 12 mm Note) For the one with outside diameter ranged between 9 to 12 remove the inside parts of the rubber seal (7) before using. 3.
240 V . 199 256 % 16 31 % 48 .5 13 23 60 182 0 lt1: o:~9 28 110 90 148 58 191 248 52 11 .2 66 StroKe 230 295 37 'h 55 15 23 70 208 0 <:::0 0 '073 34 1 . 14 40 h 56.5 15 25 80 226 0 25 g:r n 40 140 110 192 71 221 286 65 12 .5 80 ~ 80 162 130 214 72 235 306 65 14 .0 81 244 315 100 17 Series eLA Auto Switch Standard Specifications Reed Lead wire Oil proof vinyl , Impact resistance 300mIS (3D
Arm Standard 3D CAD Series Variations CKZT Series Software Equivalent 40 63 80 50 CATIA Bore size (mm) Equivalent Equivalent 30, 45, 60, 75 90, 105, 120, 135 UNIGRAPHICS Arm opening angle FIDES TURCK/P&F Switch AUTO CAD G/NPT Port thread type SOLID WORKS For additional formats, please log on to the SMC web site www.smcusa.com and click on the E-Tech icon. 184 Series CKZT Model Selection
Unit Remark Reference unit/s (default) 10n [reference unit/s] can be set. Reference unit/min 10n [reference unit/min] can be set. "%" of rated speed 10n [%] can be set. min1 (rpm) 10n [min1] can be set. Max. motor speed/40 (Hex.) Set "0" for common parameter 42. (2) Position The following units can be selected. Settings are made with common parameters 43 and 44.
31 32 35 30 30 03 32 3C 0D 06 32 OD Set at 25.0 deg.C 32 Reading internal sensor 2 01 32 05 32 36 39 0D 01 32 02 32 32 35 30 32 03 32 3F 0D Answer 25.02 deg.C 33 Reading external sensor 2 01 32 05 33 36 3A 0D 01 32 02 33 33 30 30 32 03 32 3C 0D Answer 30.02 deg.C 34 Reading alarm status 2 01 32 05 34 36 3B 0D 01 32 02 34 30 38 30 03 30 30 0D Answer ERR11 Reading offset 2 01 32 05 36 36 3D
[%F.S.] 4 3 2 1 OUT side IN side 0 0 D 2D 3D 4D 5D 0 1 2 3 4 5 Straight pipe length The smaller the piping size, the more the product is affected by the length of straight piping. The straight piping length shall be a minimum of 5 times (5D) the piping size to achieve a stable measurement.
voltage suppressor) 24 VAC 12 VDC 12 VDC 24 VDC Electrical option Other option Faston terminal 100 VAC 110 VAC 200 VAC 230 VAC DIN terminal (With surge voltage suppressor) 48 VAC 2G 2H 2V 2J 220 VAC 240 VAC 24 VAC 12 VDC 24 VDC 2K 2L 100 VAC 110 VAC 200 VAC 230 VAC 2M 2N 2P 2Q 2R 2S Conduit terminal (With surge voltage suppressor) 48 VAC 220 VAC 240 VAC 2W 24 VAC 12 VDC 24 VDC 2T 3A 3B 3C 3D
Features 1 Toggle link mechanism Proximity switch External stopper Seal Fulcrum stopper Seal (Equivalent to UL94 standard VO Flame resistant) Bumper Arm 3D CAD Series Variations Software Series CKZ2N CATIA 50 Equivalent 63 Equivalent 80 Equivalent Bore size (mm) UNIGRAPHICS Arm opening angle 30, 45, 60, 75 90, 105, 120, 135 FIDES AUTO CAD Switch TURCK/P&F SOLID WORKS For additional formats
Take proper measures to prevent dust or foreign matter from accumulating in this area. (6) (3e) VQZ (3d) (3d) (3c) VZ (3) (9) (3a) VS (3e) (8) Electrical Connection VFN (9) For wiring to DIN terminal, connect the positive (+) polar side with connector terminal no. 1 and the negative () side with connector terminal no. 2 when the rated voltage is DC type. (3e) Magnifying figure (2a) Self-up