Body Size: 10, Thread: Rc (Rc: for Sizes 20~60; M5: for Size 10), Port Size: M5 (M5 x 0.8), Mounting: None, Semi-Standard, Body Size 10: R (Flow Direction: Right to Left), Semi-Standard, Body Size 20: Standard, Semi-Standard, Body Size 30, 40, 50 & 60: Standard
Body Size: 10, Thread: Rc (Rc: for Sizes 20~60; M5: for Size 10), Port Size: M5 (M5 x 0.8), Mounting: None, Semi-Standard, Body Size 10: 3 (Drain Cock), Semi-Standard, Body Size 20: R (Flow Direction: Right to Left), Semi-Standard, Body Size 30, 40, 50 & 60: Z (Name Plate, Caution Plate for Bowl in Imperial Units: psi, °F)
Body Size: 10, Thread: None (Rc: for Body Size 20, 30, 40, 50, 60; M5: for Body Size 10), Port Size: M5 (M5 x 0.8), Option: w/o Bracket; w/o Auto Drain, Semi-Standard 1: 2R (2 + R), Semi-Standard 2: Standard
Body Size: 10, Thread: None (Rc: for Body Size 20, 30, 40, 50, 60; M5: for Body Size 10), Port Size: M5 (M5 x 0.8), Option: w/o Bracket; w/o Auto Drain, Semi-Standard 1: R (Flow Direction Right to Left), Semi-Standard 2: Standard
Body Size: 10, Thread: None (Rc: for Body Size 20, 30, 40, 50, 60; M5: for Body Size 10), Port Size: M5 (M5 x 0.8), Option: C (N.C., Float Type Auto Drain), Semi-Standard 1: R (Flow Direction Right to Left), Semi-Standard 2: Z (Name Plate, Caution Plate for Bowl, & Pressure Gauge in Imperial Units: psi, °F)
Body Size: 10, Thread: None (Rc: for Body Size 20, 30, 40, 50, 60; M5: for Body Size 10), Port Size: M5 (M5 x 0.8), Option: C (N.C., Float Type Auto Drain), Semi-Standard 1: R (Flow Direction Right to Left), Semi-Standard 2: Standard
HRX-OM-W060 Configuration One thermo-chiller for one master. 2 2 R D R D 3 3 S D S D 5 5 S G S G Master This product Do not connect any wire to other PIN numbers. Fig. 3-13 Connection of RS-232C HRL Series 3.3 Installation 3-27 HRX-OM-W060 Chapter 3 Transport and Setting Up 3.4 Piping Connect piping firmly.
Configuration One thermo-chiller for one controller. 2 2 R D R D 3 3 S D S D 5 5 S G S G Controller Master This product Do not connect any wire to other PIN numbers. Fig. 3-13 Connection of RS-232C 3.3.10 Ethernet Modbus/TCP Communication wiring This product can operate the following by Ethernet Modbus/TCP communication.
Air leakage will occur (2)For R, NPT, G thread Tightening method (5)Use R external threads with Rc internal threads and NPT external threads with NPT internal threads. Piping Caution When tightening the stud, insert an appropriate hexagon wrench to the hexagonal hole after tightening it by hand.
Leakage voltage Take note that the leakage voltage will increase when a resistor is used in parallel with a switching element or when a C-R circuit (surge voltage suppressor) is used for protecting a switching device because of the leakage voltage passing through the C-R circuit. The suppressor residual leakage voltage should be as follows. DC coil 3% or less of the rated voltage 6.
Move the piston to the stroke end of the side that will be filled with oil, and perform steps q through r in the same sequence as described above. MK/MK2 Environment UAvoid use near fire. UDon't use in the clean room. RSQ/RSG Mounting RSH UInstall the converter vertically. UInstall the converter at a position that is higher than the cylinder.
Rotary Actuated Air Gripper/2-Finger Type Series MHR2/MDHR2 Size: 10, 15, 20, 30 How to Order MHR 2 10 R Without auto switch With auto switch (Built-in magnet) MDHR 2 10 R M9N S Made to Order Refer to page 492 for details.
8 @7 @9 r t q w @8 e !5 #0 @3 !4 @4 #1 !0 y @5 !6 !7 !5 #0 @2 MK CKQ CLKQ 40 CK1 !3 !1 !2 o CLK2 Component Parts No. Description Material Qty Note No.
AU200/300 Effective thread depth 6.5 4-M5 x 0.8 AU200, 300 Float type auto-drain Port size H G F E D C B A Model Port size 1 4 / 3 8 AU200 / 50 70 61 30 40.5 31.5 164 165 AU300 50 70 61 30 40.5 31.5 188.5 165 14-3-12
Tightening torque Thread Appropriate tightening torque Nm (kgfcm) M3 M5 0.3 to 0.5 (3 to 5) 1.5 to 2 (15 to 20) Wiring 1Polarity When DC power is to be connected to a solenoid valve equipped with light and/or surge voltage suppressor, check for polarity indications.
3 EA EA y A A P P r q B EB B !4 EB !7 !1 !2 t Component Parts Aluminum alloy NBR Note No. !0 Description Material No. PBT ADC Material Note q Description Black zinc chromated Metallic plated Pilot body Body Piston guide B Valve Metallic plated !1 !2 w e Return spring Cushion Cushion Valve spring Return spring Piston B Head cover r Stainless steel Spool/sleeve Stainless steel ZDC !
Take note that the leakage voltage will increase when a resistor is used in parallel with a switching element or when a C-R circuit (surge voltage suppressor) is used for protecting a switching device because of the leakage voltage passing through the C-R circuit. The suppressor residual leakage voltage should be as follows. 4.
OUT IN BUS COM A COM B COM C COM D F R P B U S O I R DIA BF SOL RUN GATEWAY UNIT EX500 SERIES 18 19 Switch setting Open the station number switch protective cover and set the switches with a sharp-pointed watchmakers screwdriver etc. NOTE 1. Be sure to turn off the power before setting the switches. 2. Be sure to set these switches before use.
With end lock (R) Functional option Axial piping type (P) For details of adjuster and functional option, refer to pages 94 and 95 in Option Specifications.
When r the center shaft lowers, t the bearing holder plate is pressed, and the table is locked.