Electric Actuator ／ Slider Type High performance Battery-less absolute encoder Select Nil, S, or T for DeviceNetTM or CC-Link. Select Nil, 1, 3, or 5 for parallel input. 5 -
Caution Actuator and controller are sold as a set. When purchasing without controller, make sure that the combination of actuator and controller is correct.
Move Speed Position Accel PushingF T riggerL V PushingSp Moving F Area1 Area2 In posn mm/s2 mm/s mm mm/s2 mm/s mm mm mm 0 Absolute 100 20.00 1000 1000 0 0 0 100 18.00 22.50 0.5 1 Absolute 50 10.00 1000 1000 70 60 5 100 6.0 12.0 1.5 63 Absolute 20 5.00 500 500 0 0 0 100 3.0 8.0 1.2 6.
area at exhaust side (mm2) AEA 40 1.25-3.5M, 1.25Y-3L, 1.25-3M 36 S at P2=0.5 MPa BEB Although A-, COM+ and Bmarks are indicated on the Note 1) Maximum operating pressure of solenoid valve is 0.9 MPa. terminal block, VFR3000 can be used as either +COM or Note 2) Set the pressure within operating pressure range of -COM. solenoid valve.
Detachment To detach a socket from a connector, pull out the lead wire while pressing the socket s hook with a stick having a thin tip (approx. 1 mm). If the socket is used again, spread the hook outward.
Mount the marker (EX600-ZT1) into the marker groove as required. -18No.EX-OMN0032-D SI unit Model Indication and How to Order EX600-S SI unit Polarity of output Symbol Content Protocol 1 PNP (-common) Symbol Content 2 NPN (+common) EN EtherNet/IPTM Summary of Product parts No.
How to Calculate Flow Rate IP67 Enclosure Conversion with sonic conductance C: S=0.5XC Q : Air flow rate [dm3/min(ANR)] S : Effective area [mm2] P1 : Upstream pressure [MPa] P2 : Downstream pressure [MPa] t : Temperature [] Wiring connection for models conforming to IP67 should also have enclosures equivalent to or of stricter than IP67. 11 No.VQC1000V-OMM0002-B VQC1000/2000 series Specific
(mm 2) AEA Applicable terminal: 90 77 S at P 2=0.5 MPa BEB 1.25-3.5M, 1.25Y-3L, 1.25-3M Although A-, B+ and Bmarks are indicated on the terminal block, VFR5000 can be used as either +COM or -COM. 10 VFR5000-OMA0001-B VFR5000 Series 5 Port Solenoid Valve / Specific Product 4 Be sure to read before handling.
Table 7-1 Quality standard for fresh water (tap water) Item Product Standard value For circulating fluid pH (at 25oC) 6.0 to 8.0 Electric conductance (at 25oC) [S/cm] 100 to 300 Chloride ion [mg/L] 50 or less Standard Sulfuric acid ion [mg/L] 50 or less item Acid consumption (at pH 4.8) [mg/L] 50 or less Total hardness [mg/L] 70 or less Calcium hardness [mg/L] 50 or less Ion silica [mg/L
Grease pack part numbers: GR-S-010 (Net weight: 10g), GR-S-020 (Net weight: 20g) 1) Piston seal Apply grease to the inner and outer circumferences lightly and evenly for easier mounting onto the piston. 2) Tube gasket Apply grease thinly to prevent the gasket from coming off. 3) O Ring Apply grease thinly to prevent the gasket from coming off. 4) Cylinder components Apply grease to each part
General diagnostics 1 Table. 5-2 General diagnostics 1 Bit Description Explanation 0 System fault 0: No error on Diagnostics data on I/O mapping 1: At least one error on Diagnostics data on I/O mapping has occurred 1 Valve-coil(s) short circuit 0: No valve coil(s) have a short circuit 1: At least one valve coil has a short circuit 2 Module error 0: No module has an error 1: At least one connected
Use this data as a guideline for selection, as the performance data may vary depending on the material and size of the work piece. 1) Discharge characteristics (Discharge time from 1000 V to 100 V) 2) Discharge characteristics range (Discharge time from 1000 V to 100 V) 25 2 Air flow scale: 1 Air flow scale: 2 1 20 3 Air flow scale: 3 Discharge time [s] 15 s 10 5 4 Air flow scale: 4 0 0 300
Response time 1 s or less : Other specifications are equal to standard product. Analogue output A B C Voltage output 1 V 1.5 V (1.4 V) 5 V Current output 4 mA 6 mA (5.6 mA) 20 mA : The value in ( ) is when PF2W711 is used. Rated flow range Model Min. Max.
After 3 s, the mode will reset to the measurement mode. 1 digit of the zero clear range varies with individual product differences. Residual pressure Error Perform zero clear operation again after restoring the applied pressure to an atmospheric pressure condition. Pressure has exceeded the upper limit of the set pressure range.
When equipped with a light, be careful not to damage the light Surge Voltage Suppressor For AC (There is no S type because the generation of surge voltage is prevented by a rectifier.)
No.VQ1000V-OMM0002-B 10 - VQ1000/2000 series Specific Product Precautions 3 Be sure to read this before handling How to Calculate Flow Rate Conversion with sonic conductance C: S=5.0XC Q : Air flow rate [dm3/min(ANR)] S : Effective area [mm2] P1 : Upstream pressure [MPa] P2 : Downstream pressure [MPa] t : Temperature [] No.VQ1000V-OMM0002-B 11 - When the valve is failing, use this flow chart
DIMENSIONS 29 S FILTER REGULATOR Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.
Grease pack part number: GR-S-010 (10g), GR-S-020 (20g) 3-3. Replacement Parts Refer to the catalog the parts that can be replaced. Warning 1) Maintenance should be performed according to the items above.
mm2) S at P2=0.5 MPa BEB 11 Change Direction of DIN Connector/Cable Entry Unscrew retaining screw, pull off outer cover, rotate connector block through 180.
To avoid this, indicate positions of manifold blocks for single wiring specification (S) and double wiring specification (D) on a manifold specification sheet.
Please refer below for calculation of kinetic energy. 2 1 I E E: Kinetic energy [ J ] 2 I: Moment of inertia [ 2 m kg ] : Angular speed [ s rad ] Allowable kinetic energy for the rotary actuator is limited. The limit of rotation time is obtained by calculating the moment of inertia. Please refer below to calculate the moment of inertia.