A 3-port, direct operated poppet solenoid valve, series VKF300 is compact (body width 18mm), yet still provides a large flow capacity.? The VKF300?manual overrides are located in 2 directions, on the top and on the side of the valve,?providing easy manual operation unaffected by mounting space and piping direction.? FKM (Fluoro rubber) is used for the fluid-contact rubber materials, allowing
MFLD, BODY PT, UL/CSA, 4/5 PORT SOLENOID VALVE, 316 lb
Digital Flow Switch (Remote type sensor unit) Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Refer to pages 16-14-3 to 16-14-4 for Safety Instructions and Common Precautions on the products mentioned in this catalog, and refer to pages 16-1-11 to 16-1-13 for Precautions on every series. Pressure Setting Wiring Warning Warning 1. Setting of vacuum pressure 1. Do not apply excessive pulling force on the lead wire. It may cause a malfunction or damage. 2.
Note 1) Do not use the product in an atmosphere and place where there is direct contact with chemicals. It may cause damage to the body. (Alcohol, acetone, etc. also cause damage, so be sure for the product not to be close to them.) Note 2) Do not use it in a line that is kept pressurized because it could cause the body to break.
The "10-" prefix corresponds to clean/low particle generation, and the "25A-" prefix corresponds to semi-standard products for use in secondary battery manufacturing facilities. Please contact SMC for details on the numeric symbols prefixed to series names as well as for the specifications of each series. Note that products with a 2-digit number prefixed to the part number are limited in
"10-" corresponds to clean/low particle generation, and "25A-" corresponds to semi-standard products for use in secondary battery manufacturing facilities. Please contact SMC for details on the numeric symbols prefixed to series names as well as for the specifications of each series. Note that products with a 2-digit number prefixed to the part number are limited in number.
The “10-“ prefix corresponds to clean/low particle generation, and the “25A-“ prefix corresponds to semi-standard products for use in secondary battery manufacturing facilities. Please contact SMC for details on the numeric symbols prefixed to series names as well as for the specifications of each series. Note that products with a 2-digit number prefixed to the part number are limited in
to 800 16 to 650 8 to 325 30 to 750 20 to 550 10 to 300 Actuator specification Electric 401 to 500 10 to 600 5 to 300 20 to 900 12 to 600 6 to 300 24 to 800 16 to 650 8 to 325 30 to 750 20 to 550 10 to 300 501 to 600 20 to 900 12 to 540 6 to 270 24 to 800 16 to 650 8 to 325 30 to 750 20 to 550 10 to 300 601 to 700 20 to 630 12 to 420 6 to 230 24 to 800 16 to 620 8 to 310 30 to 750 20 to
In addition, SY7120 series valves do not come with a gasket because they are the equivalent of existing SY7000 series body ported valves.
The SY7000 series body ported valve gasket assembly part number is “SY7000-GS-1.”
Do not apply excessive lateral load to the piston rod.
③ Do not position the port facing vertically downward.
④ Keep the piping as short as possible with minimal bending.
Note 1) When used as a single-side hydro unit, air may be mixed in with the operating oil. Consider periodic checks and air bleeding or changing to use as a double-side hydro unit.
If you do not plan to configure the emergency stop circuitry as described above, you can use the same power supply for the control power supply (C 24 V) and the motor power supply (M 24 V).
Note 2) Do not use KK□ series S couplers with flammable or toxic substances or with steam.
Note 3) If the surge pressure is higher than the max. operating pressure, it may cause damage to the fitting or tube.
Refer to pages 16-14-3 and 16-14-4 for Safety Instructions and Common Precautions on the products mentioned in this catalog, and refer to pages 16-1-11 to 16-1-13 for Precautions on every series. Wiring Pressure Source Warning Warning 4. How to connect contact protection box Connect the lead wires from the body and the contact protective box side indicated SWITCH.
Warning (1) Do not use in an environment where corrosive gases, chemicals, sea water, water or steam are present. (2) If using in a location directly exposed to sunlight, shade the product from the sunlight. (3) Do not mount the product in locations where it is exposed to radiant heat. (4) Do not use the product in a place where static electricity is a problem.
Other qty. 70+40(n4)/2 n=4, 8, 12, 16 80+40(n4)/2 n=4, 8, 12, 16 85+40(n4)/2 n=4, 8, 12, 16 95+40(n4)/2 n=4, 8, 12, 16 1 switch, 2 switches (Different side, Same side) 45 55 60 70 50 D-A9V 50+30(n4)/2 n=4, 8, 12, 16 55+30(n4)/2 n=4, 8, 12, 16 60+30(n4)/2 n=4, 8, 12, 16 70+30(n4)/2 n=4, 8, 12, 16 Other qty. 45+30(n4)/2 n=4, 8, 12, 16 1 switch, 2 switches (Different side, Same side) 85 90
Do not Do not use in an atmosphere containing flammable or explosive gases. Fire or an explosion can result. The product is not designed to be explosion proof. Do not Do not use the product in a place where static electricity is a problem. Otherwise failure or malfunction of the system can result.
Parameters specific to each of the actuators are set in the controller at the time of shipment from the factory.
If you want to change the corresponding actuators, you must reset these specific parameters.
The setting of these parameters must be performed at one of our factories in order to prevent problems from occurring.
Contact your local SMC sales representative to put in