CV/MVGQ L 16 60 S 5 L CVJ3 Without auto switch L S 5 L J79W 16 60 CDVJ3 With auto switch Number of auto switches Action S T Single acting, Spring return Single acting, Spring extend Built-in magnet 2 pcs. 1 pc. n pcs.
min (ANR)] Air consumption [L/min (ANR)] Air consumption [L/min (ANR)] 140 120 160 120 100 140 100 120 80 100 80 60 80 60 60 40 40 40 20 20 20 0 0 0 0 0.6 0.5 0.4 0.3 0.2 0.1 Supply pressure [MPa] 0 0.6 0.5 0.4 0.3 0.2 0.1 Supply pressure [MPa] 0 0.6 0.5 0.4 0.3 0.2 0.1 Supply pressure [MPa] ZNC60m ZNC80m 300 200 180 Air consumption [L/min (ANR)] Air consumption [L/min (ANR)] 250 160 140
If reapplication of grease is needed, apply grease specifically provided for this purpose: Maximum speed (mm/s) Grease: Product name: Grease pack Part no.: 10 g GR-L-010 150 g GR-L-150 2. Use the cylinder in applications in which the overrun will not cause any problem. 2. When dynamic seals are replaced, use a seal kit provided for each bore size.
.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com Nominal symbol C76 Mounting bracket diagram 32 40 (MPa) Lateral load applied to the rod end fR (N) Foot: L Rod side flange: F Head side flange: G 0.3 58 54 10.0 L C7640 44 0.5 40 W W W F 36 0.7 33 C7632 24 0.3 23 G 17 0.5 16 1.0 13 0.7 13 Clevis: C, D
Next, in the required specification example, the viscosity is 100 mPas and the discharge rate is 2.7 L/min. Since this is equivalent to 45% of the discharge rate for fresh water, 2.7 L/min 0.45 = 6 L/min, indicating that a discharge rate of 6 L/min is required for fresh water. 3.
Next, in the required specification example, the viscosity is 100 mPas and the discharge rate is 2.7 L/min. Since this is equivalent to 45% of the discharge rate for fresh water, 2.7 L/min 0.45 = 6 L/min, indicating that a discharge rate of 6 L/min is required for fresh water. 3.
(DC24V) : DC24V10% 130mA () A/B (800 /) EEPROM LED L/A1 1 L/A2 2 LED PWR ALM MS NS 20m 0 oC40 oC() 90%RH () 50M(DC500V) 210g() 230g(DIN ) [EtherNet/IP ] EtherNet/IP TM(CT-12) 10/100Mbps() Ethernet (CAT5 100BASE-TX) /() EDS 36 /36 IP 192.168.1.1254 DHCP ID 7h(SMC Corporation) 2Bh(Generic Device) D1h -12- 3.2 1 LED 2 P1P2 EtherNet/IP 3 IP IP X1X10X100 EtherNet
Start flag 0: no send Numerical data input 1 1: send Data writting RWwn Step data No 0 to 63 Operation Note) 1 1: Absolute 2: Relative H RWwn+1 L Speed 2 0 to 65500 mm/s 3 RWwn+2 2 Position 4 +/-2147483647 0.01mm 1 RWwn+3 0 H RWwn+4 L Acceleration 2 0 to 65500 mm/s2 ID1 Numerical data input H RWwn+5 L Deceleration 2 0 to 65500 mm/s2 Data writting Pushing force 1 0 to 30 10% RWwn+6 Trigger
(When L/A IN LED is OFF.) (2)Check that the connectors of L/A IN and L/A OUT communication cables are connected and there are no broken wires. (3)Keep noise sources away from the communication cable. L/A IN and L/A OUT LEDs are OFF. LINK has not yet been established. 11 : The L/A OUT LED will be OFF if the BUS OUT connector is not used.
(When L/A IN LED is OFF.) (2)Check that the connectors of L/A IN and L/A OUT communication cables are connected and there are no broken wires. L/A IN or L/A OUT LED is OFF. LINK has not yet been established. (3)Keep noise sources away from the communication cable. 11 : The L/A OUT LED will be OFF if the BUS OUT connector is not used.
L (Low) : Level that gives the alarm before static neutralization can not be performed. * When the Auto balance sensor [High-precision type] is used, set the trimmer according to the operation mode of the Auto balance sensor. e.g.)
Round type pressure gauge (with colour zone) G36-4-01-L 1 0.2MPa setting NPT G36-10-N01-L G36-4-N01-L 1 0.2MPa setting G G36-10-01-L G36-4-01-L 1 0.2MPa setting ARP20P-310AS-01 Rc Pressure gauge adaptor assembly ARP20P-310AS-N01 Aluminium die cast NPT ARP20P-310AS-F01 G ARP20P-320AS-01 Plug assembly Rc ARP20P-320AS-N01 NPT ARP20P-320AS-F01 G AR20P-370AS-01 Plug Rc AR20P-
Contents Bore size (mm) CQ2A32-L-PS CQ2A40-L-PS CQ2A50-L-PS CQ2A63-L-PS CQ2A80-L-PS 32 40 50 63 80 100 CQ2A32-L-PS CQ2A40-L-PS CQ2A50-L-PS CQ2A63-L-PS CQ2A80-L-PS CQ2A100-L-PS !4 !5 !6 Set of left nos. !4, !5, !6. Rod seal Piston seal NBR Tube gasket CQ2A100-L-PS Seal kit includes !4, !5, !6. Order the seal kit, based on each bore size.
FV4 FV4 w FV4 FV4 FV4 FV4 r 2PW 3PW 3PW 4PW 0 L L MPA MPA 2PW 3PW 4PW 10 qIN wOUT eGauge port (Inlet) rGauge port (Outlet) 1) Other range available.
Straight type Right angle type Built-in One-touch fitting With error indication LED Brackets Flat and L brackets are available.
When mounting D-A9(V)/M9(V)/M9W(V)/M9A(V)L types on a side other than the port side with 32 to 50 cylinders, order auto switch mounting brackets separately.
For details, refer to page 10-20-40. 10-12-16 Stroke Reading Cylinder Series CE1 12, 20, 32, 40, 50, 63 How to Order CE1 32 200 L J79W Number of auto switches Mounting style Auto switch B L F G D Both ends tapped style (Standard) Bore size Nil Without auto switch Nil 2 pcs. Foot style 12 20 32 40 50 63 12 mm For the applicable auto switch model, refer to the table below.
Description Body class Symbol Bracket assembly LQ-GBL J, K 1, 2 J type K type 1, 2, 3, 4, 5, 6 L, M L type M type (for short piping) Table 1 Tubing size symbols Part No. Description Replacement parts Tubing O.D.
size (S) PB Port size G1/2 Compatible heavy-duty cord Cable O.D. 6 to 12 L L K 2-M Thread depth 6 K 2-M Thread depth 6 (mm) Electrical entry P Port size B Model A C D E F K L M Grommet: G Conduit: C DIN terminal: D Conduit terminal: T S 68 71 74 74 U 81 91.5 101 103.5 S 51 54 57 57 Q 98 101 104 104 R 36 44 53 55.5 R 40 48 56 58.5 Q 46 50 52 52 R 36 44 53 55.5 Q 63 66 69 69 R 35 42 51 53.5
) 27 79 X PE 41.5 30.5 32 R1 R2 27 P 15.5 14.5 G1/2 Electrical entry Rc1/8 PE port 19.5 (21) 19.5 Rc1/8 External pilot port (21) 31 31 5-Rc1/4, 3/8 P, A, B, R1, R2 port ( ): Rc3/8 0 1 0 1 0 1 0 1 3 position double check: VQ460 l 0 1 2 position double: VQ420 l 3 position closed center: VQ430 l 3 position exhaust center: VQ440 l 3 position pressure center: VQ450 l 181 108 73 90 50 11(A port