c Do not use in locations having an explosive atmosphere. 2. Do not operate in locations where vibration or impact occurs. Caution 3. In locations near heat sources, block off radiant heat. 1. Check the model number, size, etc. before installing. The TLM and TILM series do not have the model number displayed on the product due to the resin material used.
Do not disassemble the cables. Use only specified cables. 3. Do not connect or disconnect the wires, cables and connectors when the power is turned on. Caution 1. Wiring securely. Do not apply any voltage to the terminals other than those specified in the Operation Manual. 2. Wire the connector securely. 3. Take appropriate measures against noise.
KFG201 2 to 3 KFG203 KFG204 KFG206 Piping Method Caution 3 to 4 KFG207 KFG208 5 to 6 KFG209 KFG210 8 to 10 KFG211 KFG212 10 to 12 KFG213 KFG216 16 to 18 (1) Take a tube having no flaws on its periphery and cut it off at right angles. (Use SMC's tube cutter TK-1, 2, 3, 5 or 6 for cutting. Do not use pinchers, nippers or scissors, etc.)
Do not use the valves in an atmosphere having corrosive gases, chemicals, salt water, water, steam, or where there is direct contact with any of these. 2. Do not use in locations subject to vibration or impact. 3. Do not use in locations where radiated heat will be received from nearby heat sources. 4.
Do not operate with the magnetic coupling out of position. If the magnetic coupling is out of position, push the external slider (or the piston slider by using air pressure) back to the proper position at the stroke end. (When pushing the external slider, do not push it with bare hands.) 4. Do not apply lubricant, as this is a non-lube product.
There may be the case it will vary substantially depending on an ambient environment. 16 Series CLK2 Auto Switch Mounting Bracket / Part No.
Content 12 MK-12-PS 16 MK-16-PS 20 to 32 Bore size (mm) Not able to disassemble Set of nos. above @4 @5 @6 @7 @8 Seal kit includes @4 to @8.
MK/MK2 RSQ/RSG RSH q Do not operate the cylinder horizontally. w Do not perform work in the rotational direction. CE1 CE2 ML2B ML1C REA REC Figure 3 Figure 4 RHC e Do not clamp during a rotational stroke. MTS CC Figure 5 t Make sure that the workpiece does not move during clamping. r Do not clamp on a slanted surface.
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Do not use the product in an environment where corrosive gases or fluids could be splashed. Otherwise damage to the product and malfunction can result. Do not use in an area where surges are generated.
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
The power supply will be short circuited if inputs and outputs are connected incorrectly for the 8 point/16 point input/output units following a branch unit. 3. Do not wire with power lines or high voltage lines.
Refer to Trouble No.13 Buttons do not work. The body of the Refer to Trouble No.14 pressure switch has become loose. There is noise. Refer to Trouble No.15 Refer to Trouble No.16 -56No.PS-OMS0007-H Troubleshooting list Problem No.
Open/ Close success: default output DO[101] Open / Close failure: default output DO[102] workpiece drop detection: default output DO[103] * Digital output port can be selected within DO[101] to DO[112] * you select the same digital output port for different status signals, a warning message will be displayed. 2. Test run The manual operation of the air gripper unit can be checked.
Do not use the product in an environment where corrosive gases or fluids could be splashed. Otherwise damage to the product and malfunction can result. Do not use in an area where surges are generated.
Item Reference page 16-2-30 Output type Example of internal circuit and wiring 16-2-31 Auto shift function, Anti-chattering function 16-2-32 Measures to be taken when error occurs 16-2-33 16-2-38 15 Series ZSE60F/ISE60 High Precision, Digital Pressure Switch for General Fluids Dimensions Bracket A A 30 20 ZSE ISE 20 PSE 45 Z I SE3 55 4.5 11.5 40 15 PS 4.5 Z I SE1 2 Courtesy of Steven Engineering
Refer to each construction drawing on the fittings and tubing material. (2) Do not expose the product to direct sunlight for an extended period of time. (3) Do not use in a place subject to heavy vibration and/or shock. (4) Do not mount the product in locations where it is exposed to radiant heat. (5) Do not use the ordinary fittings and tubing in locations where static electricity would
Do not attempt to insert or pull the pressure sensor or its connector when the power is on. 3. A cable with a right-angled connector is also available. The right-angled connector faces down (toward the piping). Do not attempt to rotate the connector, as it is not rotatable. 16-2-52 9 Series ISE70/75/75H Specific Product Precautions 1 Be sure to read before handling.
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.