ZSE30/ISE30 Our pressure switches do not have an explosion proof rating. Never use in the presence of an explosive gas as this may cause a serious explosion. 3. Do not use in an environment where static electricity can cause problems, otherwise system failure or malfunction may result. 1. Do not drop, bump, or apply excessive impacts (980 m/s2) while handling.
When it goes OFF (when an alarm is generated), the controller output should be stopped by the sequence program. 24V, 0.2A or more 24V power supply + 10m or less 5) The LSP and LSN signals do not require wiring, because they are automatically turned ON internally at the time of shipment.
No.7 No.8 No.8 No.9 No.10 No.11 No.12 No.13 No.14 -78No.PS-OMV0008CN-E No.
When this is done, take care that the coverings of the lead wires do not enter the core wire crimping area. (Crimping tool: model no. DXT170-75-1) Caution Refer to pages 16-14-3 to 16-14-4 for Safety Instructions and Common Precautions on the products mentioned in this catalog, and refer to pages 16-111 to 16-1-13 for Precautions on every series.
Bracket ISA-14 DIN rail ISA-5-m L Stations Part no.
21 29 14 21 29 11.5 18.5 26 Note 1) Cannot be used with gases.
pressure (Element replacement differential pressure) Relief valve open pressure Note 1) There may be scratches, discoloration, slight paint peeling, or other defects which do not affect the product's function or performance.
Positioning complete signal 19 OZ+ Z Z 10 20 COIN OZ+ 14 GND VDC 12 to 24V 13 4.7k COM Torque monitor: Zout 4.7k 12 + IM VDD 30V max. 15mA max. 11 Speed monitor: Zout 4.7k 4.7k SP + 21 CZ Z (Pin 14 is GND.) 26 FG CN I/F 205 Non-standard Motor Compatible Drivers Mitsubishi Electric Corporation Drivers for LJ1, LG1, LX Dimensions (RS-232C without optional unit) Driver 5 100 40 1-5 hole 5
(Do not adjust more than 2mm, as it will not be possible to obtain smooth acceleration and deceleration.) Do not adjust based on the stopper's movement, as this can cause cylinder damage. Stroke Adjustment Loosen the round head Phillips screws, and remove the top covers and dust covers (4pcs.).
Refer to pages 14-21-3 to 14-21-4 for Safety Instructions and Common Precautions. AMR3000/3100 Rc 4 1 Outlet pressure (MPa) Outlet pressure (MPa) Mounting/Adjustment Set point Set point Warning F.R.L. 1. Do not place a magnetic object near the pressure switch. Unintended operation may result. 2.
Do not operate with the magnetic coupling out of position. If the magnetic coupling is out of position, push the external slider by hand (or the piston slider with air pressure) back to the proper position at the stroke end. 3. Do not apply a lateral load to the external slider.
Do not cover the inlet and outlet vents.
Do not service machinery/equipment or attempt to remove components until safety is confirmed. 1. Inspection and maintenance of machinery/equipment should only be performed after confirmation of safe locked-out control positions. 2. When equipment is to be removed, confirm the safety process as mentioned above.
Do not service machinery/equipment or attempt to remove components until safety is confirmed. 1. Inspection and maintenance of machinery/equipment should only be performed after confirmation of safe locked-out control positions. 2. When equipment is to be removed, confirm the safety process as mentioned above.
Do not drop, dent, or allow excessive impact to cylinder during handling. 5, Keep at least 20mm away from each other when 2 or more cylinders with high magnetic field resistance auto 3. switch are mounted in parallel. up, although the auto switch will function. Do not exceed specified current or the LED might be damaged and not functjon.
Do not drop, dent, or allow excessive impact to cylinder during handling. 5, Keep at least 20mm away from each other when 2 or more cylinders with high magnetic field resistance auto 3. switch are mounted in parallel. up, although the auto switch will function. Do not exceed specified current or the LED might be damaged and not functjon.
Do not operate a cylinder with its bumper bolt removed. If the bumper bolt is removed, the piston hits the head cover, causing damage to the cylinder. Therefore, do not use a cylinder without a bumper bolt. 2. The piston rod must be retracted when mounting the cylinder.
Do not warm the coil assembly with a heat insulator, etc. Use tape, heaters, etc., for freeze prevention on the piping and body only. They can cause the coil to burn out. Caution Direction of mounting 3. Avoid sources of vibration, or adjust the arm from the body to the minimum length so that resonance will not occur.
SI 1 x 2 x ( 2.5mm = 1.3 Nm) . 3-3 IP65 14 No.EX-OMU0020CN 3.2.
90 MRHQ25S MRHQ25C 14 25 1560 180 Note) Values do not include auto switch weight.