AME Design AT Caution Maintenance Caution IDl q Do not use this product in a line in which the pressure pulsation cycle is frequent. If it must be used under such conditions due to unavoidable circumstances, contact SMC beforehand. w Do not use it with anything other than dry air (such as air containing moisture).
Do not leave out the component parts when the piping port location is changed. Even if one of the component parts is not replaced, malfunction may occur, resulting in dangerous operation. 2. To prevent air leakage, re-wind the pipe tape and fit into the changed location when the piping port location is changed.
O F S TAT I O N S Correct 1 1 station to 6 6 stations W I R I N G DO NOT chamfer the nozzle No terminal box L Terminal Box wiring on Left Hand Side R Terminal Box wiring on Right Hand Side O P T I O N B Bracket G Gauge Incorrect D I M E N S I O N S S E E P A G E 7.16 Courtesy of Steven Engineering, Inc. ! 230 Ryan Way, South San Francisco, CA 94080-6370 !
OUT(2) 1 Thread type Rc NPT G Nil N F IN(1) Voltage 1 2 3 4 5 6 36 100 VAC 200 VAC 110 VAC 220 VAC 24 VDC 12 VDC 230 VAC Port size Class 3 Port size 1/8 (6A) 1/4 (8A) Class 2 Class 4 Symbol 01 02 03 04 06 3/8 (10A) 1/2 (15A) Class B in AC has a rectifying circuit built-in. Class H is AC only. No rectifying circuit.
Orifice and Port Size Combinations Orifice size (mm) Class Port size Note) T Conduit terminal TL Conduit terminal with indicator light 2 3 4 5 7 10 D DIN terminal DL DIN terminal with indicator light DO DIN terminal (without connector) 1/8 (6A) 2 1/4 (8A) 1/4 (8A) 3 3/8 (10A) 1/2 (15A) 1/4 (8A) 3/8 (10A) 4 1/2 (15A) 3/4 (20A) Connector Note) 10 is available only for N.C.
Do not disassemble the product or remove parts as it could cause breakdown of the product. 2. Flow rate is controlled by balancing the valve body. Do not expose the product to external vibration and impact as it changes the flow rate. Vibration may occur depending on the piping conditions or control methods.
Do not use this aftercooler in an area that has viscous dust (electrostatic paint powder, oily particles, etc.). If it must be used under such conditions due to unavoidable circumstances, please contact SMC beforehand.
Do not indicate suffix N for no lead wire on D-A3/A44/G39/K39 models. Lead wire length symbols: 0.5 mNil (Example) M9NW 1 m M (Example) M9NWM 3 m L (Example) M9NWL 5 m Z (Example) M9NWZ None N (Example) H7CN -X Individual -X Since there are other applicable auto switches than listed, refer to page 1214 for details.
Contact Protection Boxes/CD-P11, CD-P12 Auto Switch Internal Circuits Reed switches
B Z + Stroke DB DX DD 90 B 4DT A DS DH 4DR DB DU DO DO DC DE DU DL Rotation (mm) No.
Do not repair the fittings or patch the tube for reuse. KC 4. After operation at a high temperature, leakage may occur due to time dependent change of the tube material. If leakage occurs, remove the tube, cut off the connecting part of the tube, and connect to the piping again. Check if the tube dimension accuracy is within the recommended tolerance.
Make sure that dust and/or other foreign materials do not enter the valve from the unused port (e.g. exhaust port). The grommet portion contains a breather hole for the core.
Do not use this aftercooler in an area that has viscous dust (electrostatic paint powder, oily particles, etc.). If it must be used under such conditions due to unavoidable circumstances, please contact SMC beforehand.
Do not use this aftercooler in an area that has viscous dust (electrostatic paint powder, oily particles, etc.). If it must be used under such conditions due to unavoidable circumstances, please contact SMC beforehand.
Do not turn off the power supply before the storage completion message is received.
Do not turn off the power supply before the storage completion message is received.
Do not service or attempt to remove product and machinery/ equipment until safety is confirmed. 1. The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed. 2.
Furthermore, do not ground the shielding wire (SD). Crimping connector for division 1-6-114 Base Mounted Series SX3000/5000 Type SV Mitsubishi Electric Corporation CC-LINK System Type SH NKE Corporation Uni-wire H System Type SU JEMANET (JPCN-1) DIP.SW B RATE STATION NO.
Furthermore, do not ground the shielding wire (SD). Crimping connector for division 1-6-114 Base Mounted Series SX3000/5000 Type SV Mitsubishi Electric Corporation CC-LINK System Type SH NKE Corporation Uni-wire H System Type SU JEMANET (JPCN-1) DIP.SW B RATE STATION NO.
So, do not use under such conditions. Caution 1. Tightening the fittings and their torque When screwing fittings into the valve, make sure to tighten them to the proper torque values given below. Connection thread: M5 First, tighten by hand, then use a wrench appropriate for the hexagon flats of the body to tighten an additional 1/6 to 1/4 turn.