NCY2 series Deliberate blore use on how to connecl so as to ab9orb the displacemnt as descnbed on the right. (See ihe separale instruction manuallor how lo connect,) 4 The allowable load (relerence value) in case ot a vertical op6ration i9 shown in How lo Selecl on P.6.
This acceleration process can be achieved smoothly (as a SINE function) by using a cushion spear on which a U-shaped groove is machined. The piston stops at the stroke end on rod side with smooth cushioning. Air flow which is switched by solenoid valve is reversed from the one indicated in the above "1 Inrush". 6. Reset 3.
Deliberate blore use on how to connecl so as to ab9orb the displacemnt as descnbed on the right. (See ihe separale instruction manuallor how lo connect,) 4 The allowable load (relerence value) in case ot a vertical op6ration i9 shown in How lo Selecl on P.6.
Calculate the moment of inertia for A and B separately as shown in the figures on the right. A part B part Procedure Calculation Calculation example 1. Check the operating conditions, dimensions of attachment, etc. Operating model: MHY2-16D Opening time: 0.15 s a = 40 (mm) b = 7 (mm) c = 8 (mm) d = 5 (mm) e = 10 (mm) f = 12 (mm) A part a b c B part e f d 2.
As a rule, it should be turned about 90 beyond the point at which tightening can be felt. A B When auto switch D-Y69A is used Auto Switch Hysteresis Auto switches have hysteresis similar to micro switches. Use the table below as a guide when adjusting auto switch positions, etc. Max.
Press Part A by hand for temporary fixing. Press in the central part of Part A vertically with a tool such as pliers. A sensor connector cannot be taken apart for reuse once it is crimped. If the wire arrangement is incorrect or if the wire insertion fails, use a new sensor connector.
tool such as a spanner to prevent them from twisting.
Relief valve The use of a relief valve as the cushion valve (pressure control) provides a better cushioning effect as compared with needle adjustment on a general purpose cylinder (flow control). Operating Principles 1. Before cushioning starts Air passes through the space between the cushion seal and piston rod to the supply/exhaust port.
These units cannot be used in an environment or in a location that is exposed to synthetic oil, thinner, acetone, alcohol, organic solvents such as ethylene chloride, chemicals such as sulfuric acid or nitric acid, cutting oil, kerosene, gasoline, or a threadlock agent, etc., because they will be damaged.
Note 1) When tightening an auto switch mounting screw, use a watchmakers screwdriver with a grip diameter of 5 to 6 mm. Also, set the tightening torque to be 0.05 to 0.1 Nm. As a guide, turn 90 from the position where it comes to feel tight.
L 5 to 6 Straight bladed watchmaker screwdriver Switch mounting screw (M5 X 4l) When auto switch D-Y59 A is used B Auto switch L Note) Use a watchmakers screwdriver with a grip diameter of 5 to 6mm to tighten the auto switch mounting screw.Use a tightening torque of 0.05 to 0.1Nm. As a rough guide, tighten the screw an additional 90 after feeling a tighten resistance.
Apply class 1 turbine oil (ISO VG32) as a lubricant. Use of other lubricants may cause malfunction.
For example, the bore size to move a workpiece with a weight of 37 kg requires a bore size of 43 or more.
equipment such as a voltmeter.
Load is an analog input equipment such as a voltmeter.
Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Caution: Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Warning: Danger : Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.
Install a solenoid valve for braking as close to the cylinder as possible. If there is a long distance between the cylinder and valve, it may cause fluctuations in the stop accuracy or unexpected sudden slide table movements.
Install a solenoid valve for braking as close to the cylinder as possible. If there is a long distance between the cylinder and valve, it may cause fluctuations in the stop accuracy or unexpected sudden slide table movements.
X Other spcificanons a the same as lor standard tvDe. Cold resistant packing material allows use of the cylinder from -67" F to 158" F. X Olhr specificalions are lhe same as lor $andard lype. r.rc"rel raiGtin=sl IFFFEI--IF]@]xes There is no stick-slip phenomenon at a low-speed drive of 10-50mm/s, (0.2 2 in/s), and all strokes drive at a constant speed smoothly.