SMC Corporation of America
Elite Part Number Search
Search Results "AV2000-N02-3DB-RZ-A"

(When port sizes for A, B ports are mixed, indicate C4 or C6 in cell .)

Then, a correct operation works until a vacuum pressure proportional to the input signal is reached, and a vacuum pressure is obtained which is always proportional to the input signal.

A vacuum pad is a consumable part, so it is warranted for a year after it is delivered. Also, even within the warranty period, the wear of a product due to the use of the vacuum pad or failure due to the deterioration of rubber material are not covered by the limited warranty. outdoors or in a place exposed to direct sunlight. 2.

None K Lock Nut Hexagonal Width across Flat (Special Order) N Nickel Plating A R E A C O D E Ambient and Fluid Temp 0 ~ 60OC / 32 ~ 140F ...

Caution Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. Warning 1.

To connect a drain discharge pipe, use a pipe with a minimum bore of 10, and a maximum length of 5 m. Avoid using a riser pipe.

Warning: WARNING indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Piping Piping specification: -02 and -N02 After hand tightening, tighten the fitting using a spanner on the flat surfaces of the fitting. The tightening torque must be 8 to 12 Nm.

Piping specification: -02 and -N02 After hand tightening, tighten the fitting using a spanner on the flat surfaces of the fitting. The tightening torque must be 8 to 12 Nm.

If a directional switching valve (solenoid valve, mechanical valve, etc.) is mounted on the supply side of the regulator and repeatedly switched ON and OFF, wear of the nozzle/flapper section will be accelerated and a discrepancy in the setting value may occur. Therefore, avoid using a directional switching valve on the supply side.

M E N S I O N S AD S E R I E S A U I T O D R A I N S S Y M B O L S H O W T O O R D E R A U T O D R A I N S E R I E S AD AD402-02 (1/4) PT AD402-03 (3/8) PT AD402-04 (1/2) PT AD600-06 (3/4) PT AD600-10 (1) PT H O W T O O R D E R A U T O D R A I N S E R I E S NAD NAD402-N02 (1/4) NPT NAD402-N03 (3/8) NPT NAD402-N04 (1/2) NPT NAD600-N06 (3/4) NPT NAD600-N10 (1) NPT FOR FURTHER TECHNICAL DETAILS

Piping options: Side piping, Bottom piping A variety of actuator types.

Rc(PT) 12 04 o Bracket B o o Bracket o o @ L-bracket Connection NPTl/4 N02 a o Connection NPT3/8 N03 a o o tr 6 . 9 o u t = ^ O v o EL o Connection NPTl/2 N04 o Connection G(PD 1/4 F02 o o Connection G(PR 3/8 F03 o o Connection G(PR 1/2 F04 o O: Standard specifications O: Combination possible Blank: Combination not possible Modular Connection Part Numbers muxm : Air filter NAF3OOO NAF4OOO

Series AV is a soft start up valve for low-speed air supply to gradually raise initial pressure in an air system and for quick exhaust by cutting off air supply.

Series AV is a soft start up valve for low-speed air supply to gradually raise initial pressure in an air system and for quick exhaust by cutting off air supply.

Series AV is a soft start up valve for low-speed air supply to gradually raise initial pressure in an air system and for quick exhaust by cutting off air supply.

Non inductive (A) Non inductive (A) Model Load Load resistance Light load Inductive load Motor load Load resistance Circuit Rated voltage (V) N.C.

Non inductive (A) Non inductive (A) IS3 10 Model Load Load resistance Light load Inductive load Motor load Load resistance IS3100 (Gasket piping) IS3000-02 (Rc 1/4 thread) Circuit Rated voltage (V) N.O.

Note 1) External pilot type Main valve: 0 to 0.9 MPa Pilot valve: 0.15 to 0.9 MPa Note 2) The standard body can not be retrofitted with a foot bracket. Model Actuator part no.