Escapements Series MIW/MIS ø8, ø12, ø20, ø25, ø32 1 16 Series MIW/MIS Specific Product Precautions 1 Be sure to read before handling.
16 Series MIW/MIS Specific Product Precautions 1 Be sure to read before handling.
Caution Mounting 1) Do not subject the gauge to shocks, such as dropping during transportation and mounting, as this can cause loss of indication accuracy. 2) Do not use this gauge in a location with high temperature and humidity, as this may cause faulty operation. 3) When mounting the pressure gauge, be certain to use a wrench on the square wrench flats to screw it into place.
Mo(rntlng Bas MT33&rl 16. 2 Mounlhg 8a Sclws M5x10 DIRECTIOIIAL AIR VALVES DIMENSIONS/PARTS LIST 3125 3145 NVS 31 SEFIES NVS 3115, NVS 3125 FOOT rOUa{T[{c Prlmary mountlng mlhod ls fool mountlng on the nd of th6 body.
Refer to pages 16-14-3 to 16-14-4 for Safety Instructions and Common Precautions on the products mentioned in this catalog, and refer to pages 16-1-11 to 16-1-13 for Precautions on every series. Pressure Setting Wiring Warning Warning 1. Setting of vacuum pressure 1. Do not apply excessive pulling force on the lead wire. It may cause a malfunction or damage. 2.
However, do no rotate the cushion valve exceeding two turns, and do not rotate the speed controller valve exceeding four and half turns (40: maximum two turns). If 0.6 Nm or more of torque is applied, the valve may become loose and may jump out depending on the amount of air pressure. Cushion Adjustment The air cushion is built in on the head end for the CK1 series.
;(E a Slip exceeding retaining force may damage brake shoe, which could lead to reduced relaining force, resulting in its shorter lile a Cylinder loading should be within 35'/" of holding force when the brake is used for droo oroteclion, a Do not apply any impact when you load the cylinder in the locked position.
Caution Do not disconnect the USB cable during Teaching. If disconnected, the actuator will stop suddenly and the servo will be turned OFF.
Solenoid on side A 0 2 4 6 8 16 28 30
;(E a Slip exceeding retaining force may damage brake shoe, which could lead to reduced relaining force, resulting in its shorter lile a Cylinder loading should be within 35'/" of holding force when the brake is used for droo oroteclion, a Do not apply any impact when you load the cylinder in the locked position.
Do not disassemble the power clamp No special maintenance is necessary because the power clamp has a fully enclosed design to protect the clamp against welding spatter, and also the power clamp has a contamination resistant construction. Do not disassemble any parts other than replaceable parts, otherwise it may reduce the performance of the clamp cylinder. 3.
PAuto switch attachment Auto switches can be selected that do not protrude from cylinder body. P2 roller materials available to suit application requirements.
Proof pressure Max. operating pressure Set press. range Air operated Solenoid Ambient and fluid temperature Hysteresis Repeatability Sensitivity Mounting Lubrication Port 01 P A R mm2 02 01 02 03 04 04 06 10 10 12 14 20 02 Port size Rc(PT) 1 11 2 1 4 11 4 1 2 1 8 1 4 1 8 1 4 1 4 3 8 1 2 1 2 3 4 590 2 1 300 17 25 1.4 16 0.9 25 1.4 60 3.3 70 3.9 330 18 36 2.0 Cv 16 0.9 130 7.2 160 8.9 180 10
Do not use in lines where a pressurized condition is maintained, as the body may be damaged. Warning Caution 1. Tubing attachment/detachment for One-touch fittings 1) Installing the tubing (1) Use tubing with no flaws on its periphery and cut it off at a right angle. When cutting the tubing, use a tube cutter, TK-1, 2 or 3. Do not use pinchers, nippers or scissors, etc.
10 12 M12 x 1.25 4 4 M5 x 0.8 8 12 5 28 14.2 M4 x 0.7 19 6 15 12 10 7 6 16 12 16 M16 x 1.5 6 6 M5 x 0.8 12 17 6 38 14.2 5 M6 x 1 24 8 18.3 16 14 10 9 22 16 16 M16 x 1.5 6 6 M5 x 0.8 12 17 6 38 14.2 5 M6 x 1 24 8 18.3 16 13 10 9 22 20 20 M22 x 1.5 8 8 G1/8 16 20 8 44 17 6 M8 x 1.25 32 11 24 22 11 13 12 24 25 22 M22 x 1.5 10 8 G1/8 16 22 8 50 20 8 M10 x 1.25 32 11 30 22 11 17 12 28 Bore size
Max. 16 stations. (Specify a model with 9 to 16 stations by using a manifold specification form.)
M: Size 16, 25, 40 only.
MF EB MR 212 238 259 288 341 371 50 63 75 90 110 132 12 16 16 20 20 25 26 28 32 40 50 60 48 55 68 80 100 120 4 4 5 5 6 6 38 46 52 62 63 75 10 10 12 12 16 16 7 9 9 9 12 14 7 9 9 9 12 14 32 36 45 50 63 71 10 12 12 16 16 20 59 67.5 82.5 95 114 129 32 40 50 63 80 100 72 83 100 115 126 150 12 15 15 20 20 25 26 28 32 40 50 60 10 11 12 12 14 16 9.5 12 12 16 16 20 65 75 80 90 110 140 56 65 77 92