Ionizer How to Order IZS31 CP X13 L (Tolerance 1%) Cable length 60 L: Cable length Symbol 7 01 02 04 05 06 07 08 09 11 12 13 14 15 16 17 18 19 20 1000 mm 2000 mm 4000 mm 5000 mm 6000 mm 7000 mm 8000 mm 9000 mm 11000 mm 12000 mm 13000 mm 14000 mm 15000 mm 16000 mm 17000 mm 18000 mm 19000 mm 20 mm (Red) 1 12 (6.2) 3 Cable Specifications No. of cable wire 12 0.14 mm2 (AWG26) 0.48 mm Nominal cross section
Please order them by using the seal kit number corresponding to each bore size. 10-9-7 7 Series RSH/RS1H Dimensions/Bore Size: 20 RSH20-15 The figure shows an extended piston rod. 0.2 40 48 4-4.4 through Load carrying direction 12 3 13 28 10.3 6 3 6 12 Conveyor lower limit position 1 R25 74 Stroke 2-M5 x 0.8 14 8 144 4 Front pressure port 12 Rear pressure port 70 4.5 2-Plug 12 18 40 (Width
3 13 28 10.3 6 3 6 12 Conveyor lower limit position 1 R25 74 Stroke 2-M5 x 0.8 14 8 144 4 Front pressure port 12 Rear pressure port 70 4.5 2-Plug 12 18 40 (Width across corners 47) 36 Note 1) The figure shows dimensions at the maximum energy absorption capacity.
This weight includes the accessory weight. 23 - 12.
Precautions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate or set with wet hands. This may lead to an electric shock. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result.
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate or set with wet hands. This may lead to an electric shock. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result.
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Refer to fault signals above 32 do not operate. No.12 Input block PWR LED is OFF. Refer to fault No.13 Input block LED Refer to fault does not turn ON. No.14 Input block LED and the input data do not match. Refer to fault No.15 -35No.EX-OME0003-H Failure Problem Fault No.1 Problem Possible cause Investigation method Countermeasures Re-wire the DeviceNet cable.
12 12 13 149 159 162 178 11 11 11 12 12 12 12 13 149 159 162 178 125 135 136 151 16 16 16 16 186 201 204 230 12 12 12 13 149 159 162 178 205.5 227.5 208.5 235 230.5 255 3.1-30 SeriesCLG1 Accessory Dimensions Single Knuckle Joint Double Knuckle Joint (Knuckle pin and snap ring are packed.)
Do not use the valves in an atmosphere having corrosive gases, chemicals, salt water, water, steam, or where there is direct contact with any of these. 2. Do not use in locations subject to vibration or impact. 3. Do not use in locations where radiated heat will be received from nearby heat sources. 4.
Do not apply external force to the coil. Apply a wrench to the exterior surface of the piping joint at the time of tightening. 3. Do not use heat insulators, etc. to keep the temperature at the coil assembly. Do not use a tape heater for freeze prevention except on the piping and body. If may cause the coil to burn. Caution 1.
Note 4) Do not apply rotational torque to the rod end. Note 5) The direction of rod end width across flats (12) differs depending on the products.
Do not apply excessive force or shock to the body or fittings with an impact tool. It can cause damage or air leakage. 100 8 7 to 9 150 1/8 14 12 to 14 200 1/4 17 22 to 24 200 3/8 21 28 to 30 200 1/2 24 Lock Nut Tightening Torque Caution 1. Suitable screw torque for a hexagon lock nut is shown in the table below.
Do not ground it with devices generating strong electromagnetic noise. 3. Do not pull sensor cable strongly. Such action may cause failure. 4. Check wiring Incorrect wiring may cause damage or malfunction of the products. Make sure the wiring is correct before operation. 4. Power supply line Do not mount any switch or relay to power supply line (12 VDC to 24 VDC).
Do not cut the tubing with pliers, nippers, scissors, etc., otherwise the tubing will be deformed and problems may result. (3) When mounting the tube, resin plug or metal rod, do not press the release button. Do not press the release button unnecessarily before mounting tubing, resin plugs and metal rods.
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate or set with wet hands. This may lead to an electric shock. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result.
state auto switch RS2H 2-wire 12 V Connector RSH 3-wire (NPN) IC circuit 5 V, 12 V Relay, PLC Diagnostic indication (2-color indicator) Yes Yes Yes No No 24 V 3-wire (PNP) 2-wire MIW MIS 12 V Grommet 3-wire (NPN) IC circuit 5 V, 12 V Water resistant (2-color indicator) M9PAV1 M9PA1 3-wire (PNP) 2-wire M9BAV1 M9BA1 IC circuit 12 V 5 V, 12 V H7NF With diagnostic output (2-color indicator
12 12 13 149 159 162 178 11 11 11 12 12 12 12 13 149 159 162 178 125 135 136 151 190 16 16 16 16 12 12 12 13 149 159 162 178 186 201 204 230 205.5 227.5 208.5 235 230.5 255 3.1-30 Fine Lock Cylinder/Double Acting Single Rod Series CLG1 Construction CL MLG CNA CNG With air cushion MNB CNS CLS CB CV/MVG CXW CXS Component Parts Material Note Description Material Note Description Rolled steel
Do not use the product in an environment where corrosive gases or fluids could be splashed. Otherwise damage to the product and malfunction can result. Do not use in an area where surges are generated.
The cartridge assembly cannot be inserted while the locking knob is in the LOCK position, attempting to do so may cause damage. Do not directly touch the emitters with your finger or tools. This may result in injury.