Digital Gap Checker ( compatible) Do not use a fluid containing chemicals, synthetic oils including organic solvent, salt and corrosive gases. Otherwise damage to the product, malfunction and failure can result. Writing time of input data to product is 10 times. Design The product should be positioned higher than the detection nozzle.
Do not operate at pressures or temperatures, etc., beyond the range of specifications, as this can cause damage or malfunction.(Refer to the specifications.) Please contact SMC when using a fluid other than compressed air (including vacuum). We do not guarantee against any damage if the product is used outside of the specification range. 10.
Do not use under such conditions. (Refer to the specifications.) Please consult with SMC when using a fluid other than compressed air (including vacuum). We do not guarantee against any damage if the product is used outside of the specification range. (2)Do not disassemble the product or make any modifications, including additional machining.
Standard settings of L dimensions are with 10 or less n blocks. Ask SMC sales for the setting with over 10 blocks mounted.
(Do not tighten with pliers.)
Series 10 12 16 20 25 32 40 50 63 80 100 MHZ2 3.0 5.0 7.0 7.0 8.0 8.5 MHZL2 6.0 7.0 10.0 11.0 MHL2 7.0 8.0 8.5 10.5 11.0 12.5 MHS2 6.5 7.0 7.5 8.5 MHS3, MHS(L)3 6.5 7.0 7.5 8.0 MHS4 6.5 7.0 7.5 8.5 MHC2 30 to -10 30 to 30 to 22.5 to -10 -10 -10 MHW2 88 to 54 to 58 to 41 to 30 to -4 -5 -6 -5 -5 Air cylinder Unit: mm Tube I.D.
Do not apply excessive lateral load to the piston rod.
Do not operate beyond the rated voltage range. If applying voltage over the rated voltage range, equipment may be damaged. 2. Avoid incorrect wiring such as polarity of power supply. Otherwise, equipment may be damaged. 3. Do not short circuit the load. (Do not connect to power supply.) Otherwise, equipment may be damaged.
Outlet air atmospheric pressure dew point C P1 = 0.5MPa P1 = 0.5MPa 10 10 20 20 P1 = 0.7MPa P1 = 0.7MPa 30 30 40 40 0 40 80 120 160 20 40 60 80 0 Outlet air flow rate l/min (ANR) Outlet air flow rate l/min (ANR) IDG20 IDG30 P1 = 0.3MPa P1 = 0.3MPa 0 0 Outlet air atmospheric pressure dew point C Outlet air atmospheric pressure dew point C P1 = 0.5MPa 10 P1 = 0.5MPa 10 P1 = 0.7MPa 20 20 P1
Do not apply external force to the coil section. Surface physics Vapor deposition Charged particle beam
Do not drop or bump. Do not drop, bump, or apply excessive impacts (300 m/s2 or more for reed switches and 1000 m/s2 or more for solid state switches) while handling. Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction. 2. Do not carry a cylinder by the auto switch lead wires. Never carry a cylinder by its lead wires.
Do not drop or bump. Do not drop, bump, or apply excessive impacts (300 m/s2 or more for reed switches and 1000 m/s2 or more for solid state switches) while handling. Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction. 2. Do not carry a cylinder by the auto switch lead wires. Never carry a cylinder by its lead wires.
Do not drop or bump. Do not drop, bump, or apply excessive impacts (300 m/s2 or more for reed switches and 1000 m/s2 or more for solid state switches) while handling. Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction. 2. Do not carry a cylinder by the auto switch lead wires. Never carry a cylinder by its lead wires.
They do not guarantee an actual fixed range (expect approximately 30% dispersion).
These instructions indicate the level of potential hazard by label of Month y Z A B C D . 0 0 0 10 20 30 40 50 60 70 Do not use devices that generate electromagnetic radiation such as Jan o yo Zo Ao Bo Co Do . 0 10 20 30 40 50 60 70 Caution, Warning or Danger, followed by important safety information which must be carefully followed.
Swtting of communication speed (Switch No.8 to 10) Make sure to set the transmission speed in the range as follows. All setting are turned OFF at shipment, set to 156 kbps. Transmission speed No.8 No.9 No.10 156 kbps OFF OFF OFF 625 kbps OFF OFF ON 2.5 Mbps OFF ON OFF 5 Mbps OFF ON ON 10 Mbps ON OFF OFF -21No.EX-OMI0001-I 2.
Scale indication range Connection thread size M5 0~8 1/8 0~10 1/4 0~10 3/8 0~10 Connection Chamfer dimensionD(Recommended value) thread size 1/2 0~10 M5 5.15.4 The scale indication range is also printed on the product. 10-32UNF 5.05.3 (5) Tubing outside diameter (O.D.) of (6)-2 For R, NPT, G thread Tightening method Scale indication range When installing the connection thread, tighten it
Do not drop or bump. Do not drop, bump, or apply excessive impacts (300 m/s2 or more for reed switches and 1000 m/s2 or more for solid state switches) while handling. Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction. 2. Do not carry a cylinder by the auto switch lead wires. Never carry a cylinder by its lead wires.
Do not place the cylinder with the solenoid valve vertical. Others For manual operation, press the center of the manual override button with a blunt object. The valve is operable even if the rubber part is torn. The rubber covers do not need to be removed. Voltage fluctuation of -15 to +10% of the rated voltage is allowed.
Furthermore, do not allow excessive force to be applied to the lines. 2. Use electrical circuits which do not generate chattering in their contacts. 3. Use voltage which is within 10% of the rated voltage. In cases with a DC power supply where importance is placed on responsiveness, stay within 5% of the rated value.