RZQ 40 44 35 36 42 38.5 41.5 37.5 30.5 32.5 30 50 50 41 42 48 44.5 47.5 43.5 36.5 38.5 36 63 56.5 47.5 48.5 54.5 51 54 50 40 42 39.5 10-10-13 14 Series RZQ Mounting of Auto Switch Follow the procedures below to mount auto switches.
position, tighten the M3 mounting screw to secure the auto switch by making the bottom face of auto switch attached to the cylinder tube.
position, tighten the M3 mounting screw to secure the auto switch by making the bottom face of auto switch attached to the cylinder tube.
(Fixed SI unit [(l/min, or l, m3 or m3 x 103)] will be set for switch type without the unit switching function.) Note 3) The high flow rate type is CE marked; however, the linearity with applied noise is 5% F.S. or less. Note 4) Switch output and accumulated pulse output selections are made using the button controls.
Mount the sensor head using two M3 screws (not supplied with the product). M3 screws M3 screws M3 screws Due to the construction of the sensor, the sensor head housing is shared with GND. Install and supply power with great caution to avoid short-circuit with the +24 V power supply. The detection port is opened to detect static electricity.
Auto switch mounting screw (M3 x 0.5 x 10l) Auto switch spacer Auto switch mounting nut 4 Series RQ Dimensions/20, 25 Refer to pages 12 and 13 for proper auto switch mounting positions and height.
M3 x 0.5 M4 x 0.7 M5 x 0.8 M6 x 1 Model Applicable bolts Max. tightening torque (Nm) MHY2-10D MHY2-16D MHY2-20D MHY2-25D Model Bore(mm) Hole depth (mm) Attachment MHY2-10D MHY2-16D MHY2-20D MHY2-25D 11H9 17H9 21H9 26H9 1.5 1.5 1.5 1.5 +0.043 0 +0.043 0 +0.052 0 +0.052 0 0.88 2.1 4.3 7.4 M3 x 0.5 M4 x 0.7 M5 x 0.8 M6 x 1 (1) To mount the attachment to the finger, make sure to use a wrench
) Note 13) Note 13) Note 10) For thread type: NPT.
) Note 13) Note 13) Note 10) For thread type: NPT.
ALARM 24 Alarm output NO. 3 13 NO. 4 4 COM 12, 25 Common The output terminal common.
Note 2) When the compressor oil mist discharge concentration is 30mg/m3 (ANR). Note 3) Bowl O-ring and other O-rings are slightly lubricated. Note 4) When the outlet pressure is 0.5MPa. (The rated flow varies depending on the set pressure.) Keep the air flow within the rated flow to prevent an outflow of lubricant to the outlet side.
Standard EIA standards, RS-232C (ASCII mode/RTU mode) RD 2 RD 2 SD 3 SD 3 Circuit diagram SG 5 SG 5 This product Master Be sure to wire to the correct pin numbers according to the diagram. 5 1 9 6 D-sub 9-pin female (socket) type Communication connector 31 HRR Series Options Options have to be selected when ordering the thermo-chiller.
15.5 2 18 12 6 40 12 31 12 6 5.5 M10 x 1.25 M5 x 0.8 depth 7.5 Up to 300 16.5 10 17 19.5 2 22 14 8 40 12 38 12 6 5.5 M10 x 1.25 M5 x 0.8 depth 8 Up to 300 20 12 17 19.5 2 22 18 10 50 13 47 13 8 6 M14 x 1.5 M6 x 1 depth 12 Up to 300 26 19 16 27 2 30 25 14 58 14 58 14 11 7 M18 x 1.5 M8 x 1.25 depth 16 Up to 300 32 20 27 32 2 35 30 18 58 14 72 14 11 7 M18 x 1.5 M10 x 1.5 depth 16 Up to 300
8 15.5 2 18 12 6 40 12 31 12 6 5.5 M10 x 1.25 M5 x 0.8 depth 7.5 Up to 300 16.5 17 10 19.5 2 22 14 8 40 12 38 12 6 5.5 M10 x 1.25 M5 x 0.8 depth 8 Up to 300 20 17 12 19.5 2 22 18 10 50 13 47 13 8 6 M14 x 1.5 M6 x 1 depth 12 Up to 300 26 19 16 27 2 30 25 14 58 14 58 14 11 7 M18 x 1.5 M8 x 1.25 depth 16 Up to 300 32 27 20 32 2 35 30 18 58 14 72 14 11 7 M18 x 1.5 M10 x 1.5 depth 16 Up to 300
(mm) Bore size (mm) Stroke range (mm) 20 25 32 40 50 63 80 100 A AL B1 C D E F GA GB H H1 I J K KA MM 35 12 26 12 5 M4 x 0.7 depth 7 5 M8 x 1.25 Up to 200 14 8 13 15.5 2 18 12 6 40 12 31 12 6 5.5 M10 x 1.25 M5 x 0.8 depth 7.5 Up to 300 16.5 10 17 19.5 2 22 14 8 40 12 38 12 6 5.5 M10 x 1.25 M5 x 0.8 depth 8 Up to 300 20 12 17 19.5 2 22 18 10 50 13 47 13 8 6 M14 x 1.5 M6 x 1 depth 12 Up to
: MDHR3-10R 11221122MDHR3-10E port location 3 x M3 x 0.5 thread depth 6 P.C.D.24 A (Mounting thread) 17.5 20 120 120 40 2-3 B 8.5 25 Finger closing port M3 x 0.5 M3 x 0.5 25 Finger closing port Finger opening port M3 x 0.5 M3 x 0.5 9.5 Finger opening port 44 +0.02 2 x 3 0 depth 6 31 (A, B common view) 0 9h9-0.036 4 x M3 x 0.5 thread depth 6 2 x 4.2 (A, B common view) 9.7 4.7 1 19.5 10.1 5.8
BH BI (UU) 2-M3 x 0.5 (opposite side, same location) (For front port, use hexagon socket head set screw) Q H 2-J through JA depth of counter bore JB (opposite side, same location) 1.5 S BE CA CB BF DD D BD BG A 2.2 (0.4) Note 1) SD 16 BA 2-M3 x 0.5 depth 4 BB W 2-M3 x 0.5 (For side port, use hexagon socket head set screw) N BC Note 2) For the 180 specification, the slated line area do not
position, tighten the M3 mounting screw to secure the auto switch by making the bottom face of auto switch attached to the cylinder tube.
With Bypass Valve (Flange size: 80) (40) 148.5 3 117 (40) I G H H V A C 117 A U U M E V V A L Lead wire length: 500 mm (L type: 3000 mm) (40) XLA-16-X65 e u t w y Pilot port: Rc1/8 Bypass valve adjustment nut (Initial exhaust) Adjustment pitch: 1 mm/rotation Shaft seal (FKM) r Scraper (FKM) Pilot port: M5 0.2 Lock nut Width across flats 13 96 90 235 (Max. 13) 7.5 8-2 112 114 83 8-1 i !
SS5Y3-60Stations B (Light/surge voltage suppressor) Manual override (non-locking) Stations 2 3 4 5 6 7 8 9 10 (Station n) (Station 1) 43.3 (3.2) L1 110.5 123 135.5 148 160.5 173 173 185.5 198 33.4 (3) L2 100 112.5 125 137.5 150 162.5 162.5 175 187.5 L3 86 96.5 107 117.5 128 138.5 149 159.5 170 [44.7] L4 12 13 14 15 16 17 12 13 14 38.2 28.2 25.8 20.7 19.2 11 12 13 14 15 16 17 18 19 20 Stations