Series PF2D Digital Flow Switch For Deionized Water and Chemicals Real-time switch output, accumulated switch output, or accumulated pulse output can be selected as an output type.
In the case of adsorption on a small work piece of only a few millimeters, if an ejector is selected which has a high suction flow rate, the pressure difference when adsorbing and releasing the work piece is small. Since setting of the vacuum switch may become difficult, an appropriate ejector should be selected. 5.
Full access to this twoway databus is as simple as wiring into 2 terminals and snapping onto the yellow ASi Data Cabling. Control and output is further increased by transforming the Intelligent Valve Island into an Intelligent Node System, working within the ASi Network Domain.
The cushion effect (smooth start-up, soft stop) cannot be obtained in an intermediate stop or a return from an intermediate stop using an external stopper, etc.
Never remove valve at an angle.
2.5 to 6 6 to 20 20 to 40 40 to 63 63 to 100 AS13l1F AS13l1F AS23l1F AS33l1F AS43l1F / 1 8, / 1 4 / 1 4, / 3 8 / 1 2 Elbow (Metal Body) M5 6 to 20 20 to 32 20 to 40 40 to 63 63 to 100 AS12l1 AS22l1 AS22l1 AS32l1 AS42l1 / 1 8 4.1-7 / 1 4 / 3 8 / 1 2 In-line 6 to 20 20 to 32 20 to 40 40 to 63 63 to 100 AS1001F AS2001F AS2051F AS3001F AS4001F 4.1-9 Dual Speed Controller 6 to 20 20 to 32 20
Note 2) When used as a common external pilot, select the internal pilot specification as an applicable valve. Note 3) Gasket and mounting bolts are equipped.
-l06 to 10 ALD900-l12 to 20 D.P.
Choose the desired connecting block with the OK key Function Blocks (FB) are connected by joining an output pin to an unused input pin. The arrow is pointing to the output pin. The output pin is always shown on the right side of the function blocks. Unused Input pins are shown as > while used input pins show as a solid triangles.
2 q q AS y !3 w y t AS-FE w i t KE o AS-FG AS-FG i !0 u AS-FP !0 o e AS-FM !4 u Meter-in type Meter-out type AS-D e Seal method: Face seal For G thread AS-T Meter-in type Meter-out type ASP !1 ASN r !2 AQ q w ASV y t AK i VCHC o ASR ASQ !0 u !5 e Meter-out type Meter-in type Component Parts No.
Lightning surge countermeasures should be applied directly to system components as necessary. 2. Our pressure switches do not have an explosion proof rating. Never use in the presence of an explosive gas as this may cause a serious explosion.
value, output on-off points controlled by set values2 such as , , , and will also be rectified. 2 When an output is reversed, output on-off points displayed at , , , and will be rectified.
When not using this product as a replacement for HRG/HRGC, this function is not needed.
Actuator effective torque S x Ta (S is 10 times or more) ( ) If the mass of the clamp itself in the drawing below is considered in the calculations, it should be regarded as an inertial load. ( ) If the mass of the lever itself in the drawing below is considered in the calculations, it should be regarded as an inertial load.
Then with one side fixed, gradually close the other side and measure 2R at the point where the tubing folds or flattens, etc. 2R Fixed side How to Order Burst pressure drop curve 1.00 Length TL0604 TIL01 20 20 Symbol 20 50 100 2S Type Length 20 m 50 m 100 m 2 m Metric sizes Burst pressure drop coefficient 0.80 Roll Inch sizes 0.60 Straight Please refer to the series chart and specifications
Install an air filter. Install an air filter upstream near the valve. Select an air filter with a filtration size of 5 m or smaller. 2. Take measures to ensure air quality, such as by installing an aftercooler, air dryer, or water separator. Compressed air that contains a large amount of drainage can cause a malfunction of pneumatic equipment such as valves.
Nil N Assembled as a unit Spacer only Spacers are used to fix the stroke adjustment unit at an intermediate stroke position. Spacers are shipped in 2 piece sets.
Modules for use with external vacuum supply (from pump or mainline) or as an air driven ejector system. Safe Vacuum self-holding function by means of double solenoid valves.
VQD 24V 12V 100V 200V 110V 220V 24V DC 12V DC 100V AC 200V AC 110V AC 220V AC AXT100-20-2-05 AXT100-20-2-06 AXT100-20-2-01 AXT100-20-2-02 AXT100-20-2-03 AXT100-20-2-04 To remove manifold from DIN rail: 1) Loosen the clamp screw on the A side of both ends of the manifold. 2) Lift the A side of the manifold off the DIN rail and slide it in the direction of the B side.