EX500-GPR1A.eng Conduct an appropriate functional inspection after completing the maintenance. Do not use chemicals such as benzin and thinner to clean the product. SAFETY ( continued ) As the cables with connectors are used for all wirings among devices, the system complies with the IP65 environment.
For the external pilot valve, an "R" should be attached to the valve and the manifold part number.
M12 x 1.75 M10 x 1.5 M8 x 1.25 M Bore size Standard stroke (mm) 170 140 10 10 38 38 36.5 E B F KC GB D A 11 11 8.7 120 X T V M6 M6 M5 18.5 KA KB 46 46 38 PP 70 50 M12 x 1.75 M10 x 1.5 M8 x 1.25 N H GA C 1/4 1/4 1/8 40 P 100 63 30, 50,75, 100 40 78 73 58 66.5 61.5 48.5 4 4 3.5 8 100 90 120 160 1/8 1/8 1/8 7.5 200 160 20 20 11.5 11.5 9.5 96 Guide table10-MGF Air cylinder Rotary actuator Air
Cylinder Speed Chart Use as a guide for selection. Please confirm the actual conditions with P/A Sizing Program.
Note) When placing an order for body ported solenoid valve as a single unit, mounting bolt for manifold and gasket are not attached. Order them separately, if necessary.
Refer to p. 0-33 to 0-36 for Safety Instructions and common precautions Design Piping SlA Caution Warning VlA q Not suitable for use as a selector valve or a divider valve. The valve can malfunction due to air leakage w Not suitable for vaccum applications.
The common SUP is indicated as P on the common port and the individual SUP is indicated as R. PAX PB How to Order Manifold Arrangement of solenoid valves Write both the base part number and the solenoid valve to be mounted or blanking plate part number.
(If an SSC valve is used on both sides, perform the adjustment at the cylinder speed adjustment set needles on both sides.) After adjusting, tighten the lock nut. Keep the cylinder cushion needle on the side with the SSC valve as open as possible. 4.
An application which could have negative effects on people, property, or animals requiring special safety analysis. 4. Use in an interlock circuit, which requires the provision of double interlock for possible failure by using a mechanical protective function, and periodical checks to confirm proper operation. 1.
When transporting in an upward direction, factors such as acceleration, wind pressure and impact force must be considered in addition to the workpiece weight. Use caution particularly when lifting items such as glass plates and circuit boards, because a large force will be applied by wind pressure.
OIL Regulator for tank pressure setting Fixed orifice Mist spray unit Mixing valve Magnet holder Branch pipe Nylon tube This unit, with an oil tank and a spray ON/OFF control unit, sends oil and air to the mixing valve. This magnet holder enables the mixing valve installed on the arm end to be freely attached to the iron and steel parts such as machining tools, etc.
Series REC/Precautions Caution Speed control qThrottle speed controller, such as SMC AS series, is recommended for speed regulation.
The projection of an auto switch from the edge of the body is shown in the table below. Use the table as a guideline for mounting. Note) 2-color indicator type and perpendicular entry type protrude in the direction of the lead wire entry.
The projection of an auto switch from the edge of the body is shown in the table below. Use the table as a guideline for mounting. Note) 2-color indicator type and perpendicular entry type protrude in the direction of the lead wire entry.
With external pilot solenoids, the pilot solenoid valves are not splash proof specifications, and so care must be taken not to get fluid on oneself such as when performing maintenance. Caution Direction of mounting When replacing a valve, if an external pilot solenoid valve is mounted in the wrong direction, it may malfunction or leak air.
Select a fitting with an I.D. greater than 8 for the VP344 and the VP342; more than 10 for the VP544 and VP542, and more than 12 for VP744 and VP742 when piping length is less than 3 meters. Use an external pilot when there is a small flow outlet of the valve.
The drain pipe must have a minimum pipe bore of 10 mm, and a maximum length of 5 m (when installing an optional auto-drain).
In this case, be sure to cut the tube as perpendicularly as possible to the tube axis. (Use tube cutter TK-1, 2 or 3.) Then push the cut tube in until it comes to the flare edge, and tighten the nut by hand. Further, give nut an additional 1 turns with appropriate wrench or the like.Leave 0 space between the screwed-in nut and the tube in-line with the tube axis.
The range may vary greatly (as much as 30%) depending on the operating environment.